background image

M0412-1 ver 3.0 

 

    5 

1 INTRODUCTION 

Robot System Products

 is a front-rank provider of peripheral products for high performance 

robot applications. We provide complete tool systems solutions for your robot installations, 
aiming to improve your productivity with the most reliable and cost-effective tooling on the 
market. Continuously we explore emerging technologies, working with leading edge design. 

Robot System Products

 has a wide range of standard robot peripheral products: 

 

Tool changers 

 

Swivels 

 

Swivel tool changers 

 

CiRo 

 

Grippers 

 

Hose Packages 

 

Valve units 

 

Tool systems 

 

Tool parking systems 

 

Robot System Products’

 tool changers are constructed to maximize the flexibility and reliability 

of your robot fleet. Through our patented locking device TrueConnect™ robustness and high 
safety are combined with low weight and compactness. With our swivels compressed air, water, 
electrical and data signals as well as weld and servo power are transferred to your tools with 
robot motion capabilities fully maintained. Our Swivel tool changers 

unite the TrueConnect™ 

mechanism with our swivel technology, combining the best out of the two technologies. With 
RSPs unique Circular Rotators cables and hoses can be freely selected with high robot flexibility 
maintained, and the space requirements reduced. Our integrated Tool systems are delivered as 
complete plug-and-play solutions designed for quick and simple installation.  

Robot System Products

 product lines are available for all major robot brands and come with 

complete documentation. 3D-models for simulation are available for download at: 

www.rsp.eu.com

 

1.1 Installation and Maintenance manual 

This document describes how the swivel tool changers, STC20, STC100, STC250 and STC350, 
including corresponding tool attachments and options for transfer of power, signals and air are 
installed and replaced. In addition, the document describes required maintenance activities, 
including inspection, cleaning, lubrication, replacement of wear parts, required tools and 
products and disposal and recycling.  

The 

Product Descriptions

 of each respective unit are separate documents containing product 

information, drawings, technical data, electrical and pneumatic diagrams and lists of spare parts. 

 

 

 

Содержание P0108A





























Отзывы: