RSP M0720-1 страница 7 Скачать руководство пользователя | Manualshive

Страница: 7 / 64

background image

M0720-1 ver 3.4

7

1.2 Safety

1.2.1 General

The integrator installing  the tool changer into the system must follow the safety demands stated
in standards  and provisions applicable in the country where the tool changer system is to be
installed.  The products are all prepared for CE-certification.

The user of the Robot System Products tool changer is responsible that law and directives
applicable in respective countries, with regards to safety, are followed. The user is also
responsible to guarantee that all safety devices are installed correctly.

WARNING!

Never carry out service work on a robot that has not been taken out of operation.
See safety information for the robot.

WARNING!

Only perform work on grippers or tools attached to the tool changer if the air
pressure is safely switched off.

WARNING!

Be aware that tool changer and tool attachment are heavy and may cause personal
injury and equipment damage if dropped.

NOTE!

The tool changer shall always be in locked position, also when empty, to avoid
unexpected locking if air pressure is lost.

NOTE!

For the tool changer to comply with international safety standards like ISO 13849
and ISO 10218, double channel technology is required for control and supervision,
using valves like P6718 or P7710.

1.2.2 Explanation of warnings

The warnings in this document are specific to the products in this manual. It is expected that the
user also pay attention to certain notifications from the robot manufacturer and/or the
manufacturers of other components used in the installation.

WARNING!

The warning sign will make you aware that a situation could result in potential
serious injury or damage to equipment

.

NOTE!

The note sign will alert you about something important to consider.

«
...
5
6
7
8
9
...
»

Содержание M0720-1

































































Отзывы:

Нет отзывов

Похожие инструкции для M0720-1

Бренд: T-Drill Страницы: 75

Бренд: Zeiss Страницы: 38

Бренд: MacDon Страницы: 17

Бренд: Olympus Страницы: 50

Бренд: VAHVA Страницы: 19

Бренд: MacDon Страницы: 89

Бренд: Yates Страницы: 2

Бренд: JAC Страницы: 100

Бренд: Modulate Страницы: 2

Бренд: JB Systems Страницы: 12

Бренд: Ace Страницы: 17

Бренд: ACE INSTRUMENTS Страницы: 33

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: TapFlo Страницы: 35

Бренд: DANA Страницы: 8

Бренд: 2E Страницы: 6

Бренд: Bante Instruments Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды