RS Automation AnyTouch V8 Plus Series, Руководство по эксплуатации

Страница: 2 / 20

2
V808+ OPERATING INSTRUCTIONS
Check the appearance of the unit when it is unpacked. Do not use the unit if any damage or deformation is found.
Failure to do so may lead to fire, damage or malfunction.
For use in a facility or for a system related to nuclear energy, aerospace, medical, traffic equipment, or mobile
installations, please consult your local distributor.
Operate (or store) AnyTouch under the conditions indicated in this manual and related manuals. Failure to do so
could cause fire, malfunction, physical damage or deterioration.
Understand the following environmental limits for use and storage of AnyTouch. Otherwise, fire or damage to the unit
may result.
- Avoid locations where there is a possibility that water, corrosive gas, flammable gas, solvents, grinding fluids or
cutting oil can come into contact with the unit.
- Avoid high temperature, high humidity, and outside weather conditions, such as wind, rain or direct sunlight.
- Avoid locations where excessive dust, salt, and metallic particles are present.
- Avoid installing the unit in a location where vibration or physical shock may be transmitted.
Equipment must be correctly mounted so that the main terminal of AnyTouch will not be touched inadvertently.
Otherwise, an accident or electric shock may occur.
Tighten the fixtures of AnyTouch with a torque in the specified range. Excessive tightening may distort the panel
surface. Loose tightening may cause AnyTouch to come off, malfunction or be short-circuited.
Check periodically that terminal screws on the power supply terminal block and fixtures are firmly tightened.
Loosened screws may result in fire or malfunction.
Tighten terminal screws on the power supply terminal block equally to a torque of 10.6 inch-lbf (1.2 N·m). Improper
tightening of screws may result in fire, malfunction, or trouble.
AnyTouch has a glass screen. Do not drop or give physical shock to the unit. Otherwise, the screen may be
damaged.
Connect the cables correctly to the terminals of AnyTouch in accordance with the specified voltage and wattage.
Over-voltage, over-wattage or incorrect cable connection could cause fire, malfunction or damage to the unit.
Be sure to establish a ground of AnyTouch. Ground FG terminal which must be used for the unit. Otherwise, electric
shock or a fire may occur.
Prevent any conductive particles from entering into AnyTouch. Failure to do so may lead to fire, damage or
malfunction.
After wiring is finished, remove the paper used as a dust cover before starting to operate AnyTouch. Operation with
the cover attached may result in accident, fire, malfunction, or trouble.
Do not attempt to repair, disassemble or modify AnyTouch at your site. Ask RS Automation Co., Ltd. or the designated
contractor for repair. Otherwise, it may cause a malfunction.
RS Automation Co., Ltd. is not responsible for any damages resulting from repair, overhaul or modification of
AnyTouch that was performed by an unauthorized person.
Do not use a sharp-pointed tool when pressing a touch switch. Doing so may damage the screen.
Only experts are authorized to set up the unit, connect the cables or perform maintenance and inspection.
For AnyTouch using a lithium battery, handle the battery with care. The combustible materials such as lithium or
organic solvent contained in the battery may generate heat, explode, or catch fire, resulting in personal injury or fire.
Read related manuals carefully and handle the lithium battery correctly as instructed.
When using a AnyTouch that has analog switch resolution with resistance film, do not press two or more points on the
screen at the same time. If there is a switch between the two pressed points, it may be activated.
Take safety precautions during such operations as setting change during running, forced output, start, and stop. Any
misoperation may cause unexpected machine motions, resulting in machine accident or damage.
In facilities where a failure of AnyTouch could lead to accident threatening human life or other serious damage, be
sure that the facilities are equipped with adequate safeguards.
At the time of disposal, AnyTouch must be treated as industrial waste.
Before touching AnyTouch, discharge static electricity from your body by touching grounded metal. Excessive static
electricity may cause malfunction or trouble.
Never insert the CF card in the socket of AnyTouch with the wrong direction. Doing so may destroy the CF card or
the socket of AnyTouch.
The LED lamp on the CF card interface cover lights up in red during supplying power to the CF card. Never remove
the CF card or turn off the power of AnyTouch while the LED lamp is lit. Doing so may destroy the data on the CF
card. Check that the LED lamp has gone off before removing the CF card or turning off the power of AnyTouch.
If a LAN cable is inserted into the MJ1 or MJ2 connector on AnyTouch, the counterpart device may be damaged.
Check the indication on the unit and insert a cable into the correct position.