GUARANTEE
ALL REALLY RIGHT STUFF BRAND PRODUCTS ARE
GUARANTEED TO THE ORIGINAL PURCHASER TO BE FREE
OF DEFECTS IN MATERIALS OR WORKMANSHIP FOR FIVE
(5) YEARS FROM THE DATE OF PURCHASE. PRODUCTS
WILL BE REPAIRED OR REPLACED AT OUR OPTION.
® , ™, © 1990-2017 Really Right Stuff, LLC. All rights reserved.
MAINTENANCE
General Care
The BH-25 is finished with a protective anodize plating that protects
the aluminum from corrosion and mild abrasion. It will not protect it
from scraping against or dropping on rocks/concrete/etc.
Cleaning
Take precautions to prevent your BH-25 from getting fouled in mud, dirt,
or sand. If the BH-25 is fouled, dry dust and dirt can be blown off and/
or wiped off with a soft cloth. Mud or salt water should be lightly rinsed
off with fresh water and then thoroughly dried. If fine sand/grit fouls
the knob, simply run a gentle stream of water around the knob while
rotating it one-half turn back and forth. Do NOT submerge the ballhead
and do not direct a high-pressure stream of water at it.
INSTALL TO TRIPOD
1. Tighten the Main Lock T-Lever to lock the Panning Base.
2. Screw the ballhead onto the 3/8”-16 threaded stud on
the top of the tripod (stud should not protrude more than
3/8” above platform or 5-6 threads). Tighten the ballhead
onto the tripod snugly, but do not over-torque or it will be
difficult to remove.
USING THE MAIN LOCK T-LEVER
The Main Lock T-Lever is longer on
one end. This design makes it easy
to turn the lever and apply enough
pressure to solidly lock the head. In
some instances, though, the long
end of the lever may hit the tripod
platform or even the clamp. That’s
why we made the main lock T-Lever
spring loaded and re-positionable:
1. Pull the T-Lever out.
2. Rotate T-Lever to a new
position. The T-Lever actually
drives an internal six-sided
hex nut, so there are 6
possible positions for the
T-Lever.
3. Allow T-Lever to snap into
place.
GUARANTEE
ALL REALLY RIGHT STUFF BRAND PRODUCTS ARE
GUARANTEED TO THE ORIGINAL PURCHASER TO BE FREE
OF DEFECTS IN MATERIALS OR WORKMANSHIP FOR FIVE
(5) YEARS FROM THE DATE OF PURCHASE. PRODUCTS
WILL BE REPAIRED OR REPLACED AT OUR OPTION.
® , ™, © 1990-2017 Really Right Stuff, LLC. All rights reserved.
MAINTENANCE
General Care
The BH-25 is finished with a protective anodize plating that protects
the aluminum from corrosion and mild abrasion. It will not protect it
from scraping against or dropping on rocks/concrete/etc.
Cleaning
Take precautions to prevent your BH-25 from getting fouled in mud, dirt,
or sand. If the BH-25 is fouled, dry dust and dirt can be blown off and/
or wiped off with a soft cloth. Mud or salt water should be lightly rinsed
off with fresh water and then thoroughly dried. If fine sand/grit fouls
the knob, simply run a gentle stream of water around the knob while
rotating it one-half turn back and forth. Do NOT submerge the ballhead
and do not direct a high-pressure stream of water at it.
INSTALL TO TRIPOD
1. Tighten the Main Lock T-Lever to lock the Panning Base.
2. Screw the ballhead onto the 3/8”-16 threaded stud on
the top of the tripod (stud should not protrude more than
3/8” above platform or 5-6 threads). Tighten the ballhead
onto the tripod snugly, but do not over-torque or it will be
difficult to remove.
USING THE MAIN LOCK T-LEVER
The Main Lock T-Lever is longer on
one end. This design makes it easy
to turn the lever and apply enough
pressure to solidly lock the head. In
some instances, though, the long
end of the lever may hit the tripod
platform or even the clamp. That’s
why we made the main lock T-Lever
spring loaded and re-positionable:
1. Pull the T-Lever out.
2. Rotate T-Lever to a new
position. The T-Lever actually
drives an internal six-sided
hex nut, so there are 6
possible positions for the
T-Lever.
3. Allow T-Lever to snap into
place.
