RR Mechatronics STARRSED TL Скачать руководство пользователя страница 60

Страница: 60 / 137

6. Pip.=Sedimentation pipette number (number on the pipette belt).

7. Time=Actual sedimentation time in minutes.

8. T=Temperature (in degrees Centigrade).
9. Error=Error message (if the Analyser detects an error).

10.

EDTA mode

7.1.1 - Report 60-Minute mode

+ REPORT E

(Not to scale)

-- StaRRsed--

Date 25/04/2019

Time:

15:28

905001

CLEAR

EDTA

905002

Hazy<10mm

EDTA

905003

Hazy<25mm

EDTA

905004

Hazy>25mm

EDTA

905005

CLEAR

EDTA

905006

CLEAR

EDTA 079

905007

Too many borders found

905008

L_err(---/ 84/

75/200)

EDTA

905002/905003/905004

Sample results with hazy aspect
905005:

Sample result with a manual aspect, where the manual aspect is shown as a number

in column 6 of this

data record sample.
905006:

In this sample, the dilution rate has a dilution failure of 21% and that is printed as

EDTA 079.

905007

Sample results with a text error. This sample gives Too many borders found. Result of a pipette possibly filled

with air bubbles.
905008

Sample result with a text error. This sample is given limit error L_err(---/ 84/ 75/200)

Reporting

MRN-164_2-EN Version 1.08 Starrsed TL

Содержание STARRSED TL










































































































































Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды

RR Mechatronics STARRSED TL, Инструкция по эксплуатации

Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды