RPS MiniMag 17'' Disk Pad Assist Скачать руководство пользователя страница 13

Страница: 13 / 42

INI

-OP-EN

- 13 -

ADJUSTING SQUEEGEE:

Turning adjustment knob

(A)

clockwise

(tightening)

will

lower tips and raise the center of the Squeegee

(SEE

BELOW)

2. This Squeegee is adjusted too far back and will not

pick up on the corners

(SEE BELOW)

NOTE: Tips off of the fl oor.

3. This Squeegee is adjusted too far forward and will not

pick up in the center

(SEE BELOW)

NOTE: Center spaced off the fl oor.

4. This Squeegee is adjusted just right with good

defl ection across the entire rear blade

(SEE BELOW)

REMOVING SQUEEGEE:

1. With the Squeegee in the up position, turn machine

power off.

2. Disconnect

Vacuum

Hose

(A)

from squeegee and

loosen both knobs

(B)

(SEE BELOW)

3. Pull Squeegee assembly backward from the lifting

carrier.

4. Inspect or repair as needed and reinstall.

REPLACING OR ROTATING SQUEEGEE BLADES:

NOTICE

FOR SAFETY: Before leaving or servicing the machine,

stop on a level surface, turn off machine and remove key.

1. Remove the Squeegee assembly from the machine.

Remove Blade retainer strap and remove Squeegee
Blade.

2. Rotate the Squeegee to new edge position or replace

as required.

3. Install Blade on the locating pins of Squeegee

Assembly.

4. Install Squeegee Retainer Strap.

5. Fasten and lock knobs, starting in the center and

moving outwards.

Содержание MiniMag 17'' Disk Pad Assist











































Результаты поиска

Содержание MiniMag 17'' Disk Pad Assist

Отзывы:

Похожие инструкции для MiniMag 17'' Disk Pad Assist

Бренды по названию

Популярные бренды

RPS MiniMag 17'' Disk Pad Assist, Руководство по эксплуатации

Результаты поиска

Содержание MiniMag 17'' Disk Pad Assist

Отзывы:

Похожие инструкции для MiniMag 17'' Disk Pad Assist

Бренды по названию

Популярные бренды