background image

ROYAL HC1501 MICROCUT PAPER SHREDDER

Setup:
 1.
 Make sure that the wastebasket is completely inserted into the shredder cabinet  

    and that it fits flush with in the cabinet.
 2. Plug the power cord into any standard 115-volt AC outlet.
 3. Depress the power 

(

   

button.  The

 LED should light up.  You are now ready to  

   start shredding.

Operating the shredder:
With the electrical cord plugged in, with the 

power 

(

   

button depressed, and the 

shredder wastebasket properly in place, the LED will light up.   This means the 

shredder is now ready for operation.  When paper is inserted into the feed opening, 

the shredding process will start automatically and stop when the paper has completed 

its travel through the feed opening.  The 

power 

(

   

button is located on the top of the 

shredder. The forward and reverse buttons are also located on top of the shredder. 
Their purposes are:
 1. When the power 

(

   

)

 button is pressed, the power LED will illuminate, the 

 

    shredding process will start when paper is inserted into the feed opening and will  

   continue until it has passed through the feed opening.
 

2. The reverse button is used to assist in the removal of a paper jam, which    

   reverses the shredding process prior to a completed forward cycle, thus clearing  

    the cutters.  When switching from 

reverse to forward, always allow the motor to  

    stop to prevent possible damage to the motor.
 3. The power 

(

   

position is used to terminate the AC power to the shredder.   It is  

    recommended to turn the shredder off when the shredder is not being used for  

    a prolonged period of time.
 4. When the LED is illuminated it lets the user know that the wastebasket is inserted  

    correctly and that the shredder is turned on and ready for use.  If the LED does  

    not illuminate, make sure that the plug is plugged in, the basket is inserted    

    correctly and the 

power 

(

  

is depressed.

Shredder capacity:
The Royal HC1501 will shred up to fourteen (14) sheets of 20-lb. bond paper and will 

accept paper widths up to 8 3/4".  When shredding small material like envelopes, 

receipts or a credit card insert them in the middle of the feed opening.  Never place or 

attempt to shred CDs or DVDs in the paper feed opening. The paper feed opening is 

designed to shred paper only.  CDs, DVDs and credit cards should be placed in the 

slotted opening marked for CDs and Credit Cards.

Basket Full Sensor
The HC1501 is equipped with an electronic basket full LED and sensor.  When the 

wastebasket becomes full, the bin full LED will then illuminate.  If this occurs, empty the 

wastebasket.  You can now resume normal shredding.

Cautions:
  1. Keep all loose articles of clothing, ties, jewelry, hair or other small items  

    away from the feed opening to prevent injury.
  2. Keep the shredder turned off or unplugged when not in use for prolonged  

    periods of time.
  3. Remove all paper clips and staples from paper before shredding.   The    

    Royal HC1501 will cut staples, small paper clips and credit cards;  

 

   however, proper discretion is recommended.
  4. Do not place hands or fingers into the shredder throat as serious injury  

    could result.

2

ROYAL HC1501 MICROCUT PAPER SHREDDER

  5. When manually changing feed direction, pause long enough for the  

 

    motor to stop.
 6. Always turn off or unplug the shredder prior to moving, cleaning or  

 

    emptying the wastebasket.
  7. Empty the wastebasket frequently to avoid possible paper jams caused  
    by shredded material being pulled back into the cutter assembly. 
  8. Never allow children to shred or play with paper shredder or else serious
Paper jams and motor overload situations:
The Royal HC1501 is equipped with an automatic motor overload protection circuit. 

The duty cycle for the HC1501 is rated for continuous shredding.  The HC1501 will 

automatically terminate power in case of the following abnormal situations: 
 1. Operating the shredder at the maximum 14-sheet capacity continuously for a  
    prolonged period of time.  

 

 2. Exceeding the shredding capacity, eg. Inserting more than fourteen (14)  

 

    sheets of 20-lbs. paper in one pass, or if the paper is not fed squarely into the  

   feed opening.
Both abnormal operations may result in the activation of the automatic thermal 

motor overload protection circuit, which terminates the power to the shredder.  A 

paper jam could cause the thermal motor overload protection to terminate AC 

power to the motor. Never allow the shredder to remain in a jammed condition with 

the AC power turned on.  If this occurs you should:

In case of a minor paper jam the overload LED will light up:  
 1. Grasp the excess paper from the top and pull it out as you depress the  

 

  

reverse button.  Be careful not to place your fingers near the feed opening or  

    else serious harm could result.
 2. Make sure that all of the excess paper has been removed from the feed  

 

   opening.  You are now ready to resume normal shredding.

In case of a major paper jam the overheat LED will light up:
 1.
 Turn off or unplug the power cord from the AC outlet and wait at least 30  

 

   minutes for the thermal overload protection to reset.
 2. Plug in the AC power cord and depress the power 

(

   

)

 button.  If paper was left  

    inside the feed opening prior to the overload, press the 

reverse position and   

   grasp the excess paper from the top and pull it out.  Be careful not to place    

   your fingers near the feed opening or serious harm could result. Clear any    

   excess paper shreds from the feed opening.  
 3. You are now ready to resume normal shredding. 
Specifications:
     Shred Type: MicroCut
     Shred Width:    

21/127” X 9/20“ (4.3mm x 11.5mm)  

     

Shredding Capacity:  

14 Sheets

     Feed Opening:    

8 3/4”  

     Weight:    

31.3lbs/14.2Kg

     Input: 

115 

volt AC, 6.0 amp.

3

Содержание HC1501

Страница 1: ...der Operation Manual HC1501 MicroCut Shredder HC1501 1160 U S Highway 22 East Suite 301 Bridgewater NJ 08807 Made in China ROYAL ConsumerInformationProducts Inc Copyright Royal Consumer Information Products Inc 2014 All Right Reserved ...

Страница 2: ...n reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 If applicable connect the equipment into an outlet on a circuit different from that to which the receiver is connected Co...

Страница 3: ...ERMS OF THIS WARRANTY Please do the following 1 Send a copy of your original sales receipt showing original purchase date along with your mailing address and a note describing the nature of the problem to Royal Consumer Information Products Inc Warranty Processing 50 Hilton Street Easton PA 18042 7391 USA Do Not Return the Product to This Address 2 You will receive a return authorization number wi...

Страница 4: ...injury 2 Keep the shredder turned off or unplugged when not in use for prolonged periods of time 3 Remove all paper clips and staples from paper before shredding The Royal HC1501 will cut staples small paper clips and credit cards however proper discretion is recommended 4 Do not place hands or fingers into the shredder throat as serious injury could result 2 ROYAL HC1501 MICROCUT PAPER SHREDDER 5...

Отзывы: