background image

Troubleshooting

8

17

Problem

Cause

Remedy

Engine Fails to start

1.  Throttle lever not in correct starting position. 

2.  Spark plug wire disconnected.

3. 

Choke not in CHOKE position (if equipped).

4.  Fuel tank empty or stale fuel.

5.  Engine not primed (if equipped).

6. 

Faulty spark plug.

7.  Blocked fuel line.

8.  Engine flooded.

1.  Move throttle lever to FAST or START 

position.

2.  Connect wire to spark plug.

3. 

Move choke lever to CHOKE position.

4.  Fill tank with clean, fresh gasoline.

5.  Prime engine as instructed in Engine Manual.

6. 

Clean, adjust gap, or replace.

7. 

Clean fuel line.

8.  Wait a few minutes to restart, but do not 

prime.

Engine runs erratic

1.  Spark plug boot loose.

2. 

Unit running on CHOKE (if equipped).

3. 

Blocked fuel line or stale fuel.

 

4.  Low engine RPM.

5.  Water or dirt in fuel system.

6. 

Dirty air cleaner.

7. 

Carburetor out of adjustment.

1.  Connect and tighten spark plug boot.

2. 

Move choke lever to OFF position.

3.  Clean fuel line; fill tank with clean, fresh 

gasoline.

4.  Always run engine at full throttle.

5.  Drain fuel tank. Refill with fresh fuel.

6. 

Refer to engine manual.

7. 

See authorized service dealer.

Engine overheats

1.  Engine oil level low.

2.  Dirty air cleaner.

3.  Carburetor not adjusted properly.

1.  Fill crankcase with proper oil.

2.  Refer to engine manual.

3.  See authorized service dealer.

Occasional skips

(hesitates) at

high speed

1.  Spark plug gap too close.

2.  Carburetor idle mixture adjustment 

improperly set.

1.  Remove spark plug and adjust gap to .030”.

2.  See authorized service dealer.

Excessive Vibration

1.  Loose parts or damaged impeller.

2.  See authorized service dealer.

Unit does not discharge

1.  Discharge area clogged. 

 

2.  Foreign object lodged in impeller. 

3.  Low engine RPM.

1.  Stop engine immediately and disconnect 

spark plug wire. Clean flail screen and inside 

of discharge opening.

2.  Stop engine and disconnect spark plug wire. 

Remove lodged object.

3.  Always run engine at full throttle.

Rate of discharge slows 

considerably or composition 

of discharged material 

changes

1.  Low engine RPM.

2.  Chipper blade dull.

1.  Always run engine at full throttle.

2.  Replace chipper blade or see your authorized 

service dealer.

Содержание CS454R Series





















Отзывы: