CONTENTS
FEATURES
ADJUSTABLE GUIDE LINE
HOW TO INSTALL MIRROR MONITOR
MENU SETTING
HOW TO WIRE
SPECIFICATIONS
The package contains the following:
01 Rearview mirror monitor
02 wire harness
03 User's manual
04 wire cover
05 Remote control
Screen Brightness: 1000CD/m
2
Screen Size: 4.3 inch
Compatiable Systems: PAL / Auto / NSTC
Resolution: 480(H) X 272(V)
Working Voltage: 12V DC
Display Type: TFT-LCD
02
01
04
05
3m
1m
2m
0.4m
3m
2m
1m
How to adjust the guide line
R
Display on the monitor
L
UP
Clockwise
Down
Right
left
Move the guide line
Rotate the guide line
anticlockwise
Press the button to choose the L or R adjustable guideline
Remote control
Right position
Wrong position
Remote control
Menu setting guidance
Short press “ ”, you can switch among “PICTURE”, “SYSTEM”, “AUTO
DIMMING”, “COMPASS”, “TEMPERATURE” or exit out. When you enter either,
press “ ” to switch among the items.
“ ” and “ ” are used to change the setting of each option.
Enter the menu
Guide line clockwise
Menu parameter decreases
Menu parameter
increases
Guide line up
Guide line left
Enter guide line
adjustment
Guide line anti-clockwise
Guide line right
Guide line down
03
Removing the original mirror
CAUTION:
DO NOT USE EXCESSIVE FORCE WHEN REMOVING MIRROR
FROM THE WINDSHIELD MOUNT. THE WINDSHIELD BUTTON MAY SEPARATE
FROM THE WINDSHIELD OR THE WINDSHIELD MAY BREAK IF FORCED.
NOTE:
There are several versions of mirror mount systems. If unfamiliar with
mirror removal, seek professional assistance.
Screw mount mirror removal.
Using a Philips screwdriver or #20 Torx bit, loosen the screw in the base of
the mirror.
After loosening screw, gently lift upward to slide mirror off of mirror mount.
Wedge mount mirror removal procedure:
(Common for screw less mount).
Using a mirror tool or small 1/8” (4 mm) flat-blade screwdriver, insert the
flat end into the opening at the bottom of the mirror mount at the windshield.
Slide the screwdriver into the center of the mirror mount until resistance is
felt.
Gently apply a small amount of additional upward force to lift away locking
spring in the mount.
While still applying upward pressure with the screwdriver, grasp the mirror
bracket and wiggle side to side. Lift mirror up toward the headliner and off
the windshield mount button.
Mirror Installation.
Installation will vary depending on the mounting foot you use for the vehicle.
The mount pre-installed on the mirror is for a standard wedge mount foot. If
you need to use a different foot, change the foot by removing the Philips
head screw in the center of the foot. Attach the required foot to the mounting
arm with the included screw.
NOTE:
Check to insure the center screw in the mounting foot is tight before
installation to the windshield. The center screw should be tightened to 15
in-lb. If changing the mount, we recommend using Loctite Threadlocker to
insure the mount will not loosen over time. Install the mirror by reversing the
removal process.
NOTE:
Always use caution, DO NOT force the mount. Rostra Precision
Controls, Inc. will not be responsible for broken windshields. If you are not
sure how to remove or re-install the mirror seek trained, qualified help.
The menu is accessed and set by using the remote control.
The monitor is equipped with adjustable guide lines that should be set
correctly at the time of installation. Generally, these guidelines are used to
help drivers estimate the distance from obstacles when parking. There are
three lines for reference-Red, Yellow and Green. These three lines are
displayed on the monitor when car is in reverse. The lines should be adjusted
so the green line starts approximately 9ft away from the rear of car, the
yellow line starts approximately 6ft away from the rear of car, and the red
line starts approximately 3ft away from the rear of car. The lines should also
be adjusted to be approximately 6 inches wider than the vehicle on each side
to assist in parking.
Place the vehicle into reverse gear and press the guideline adjustment
key in the center of the 4 directional keys on the remote control.
For the right side press the button again to select (XR).
To adjust the angle of the guidelines press the rotation keys below the
4 position keys to rotate the lines clockwise and counter clockwise.
When you are finished place the vehicle in Park, the monitor will shut off
and the positions will be saved in the mirror’s memory.
NOTE:
The remote control must be at least 1.5 feet from the mirror when
using it for adjustments or it may not respond.
Adjusting The Guidelines
Use the up, down, left, and right buttons to adjust the location of the
selected guideline.
By placing items behind the vehicle at the measurements shown above you
will be able to easily and quickly customize the parking lines for this particu-
lar vehicle.
Once you have either marked the area or place items such as traffic cone
behind the vehicle make sure the parking brake is engaged and no one is
behind the vehicle.
FUSE
BOX
Black to GND (-12v)
Original Onstar connector from your vehicle
Red to ig12V
Green to Rev trigger (+12v)
GND
4.3" Ultra High Brightness Back Up Camera Display
One-Touch Input for Second Camera
Automatic Monitor Brightness Adjustment
4.0mm Glass
Adjustable Back up guide lines
Rear View Mirror with *Onstar compatibility
EC Auto Dimming
Compass and Temperature (option)
Mirror 10 Pin connector
10 Pin
16 Pin
Vehicle 16 Pin harness
Jumper harness
To back up camera
Front Camera in
Two original wiring connectors can work with interior rear view mirror, both 10
pin and 16 pin style connectors. Our replacement mirror is equipped with 10 pin
connector which can match the original 10 pin mirror. A converter wire harness
is included to adapt to a 16 pin if needed.
This mirror is designed to replace a mirror that does not have a monitor already.
SYSTEM
SCALE
ON
ON
OFF
REAR TRI
PRESET
PICTURE
BRIGHTNESS
50
50
50
CONTRAST
COLOR
00
NIGHT BRIGHTN.
Picture:
•Brightness–Adjust the daytime
screen brightness level
•Contrast–Adjust the screen contrast
•Color–Adjust the screen color
•Night Brightness–Adjust the night
time screen brightness level
System:
•Scale–Turns Guidelines On/Off
•Language–Select the Menu language
•Preset–Off/On –On Selects the factory
setting for the guidelines.
To enter the Settings Menu first engage the parking brake and have
your foot firmly on the brake pedal while making adjustments.
