Rosslare AYC-E 5 Series Скачать руководство пользователя страница 9

Страница: 9 / 65

Introduction

AYC-Ex5/T65 Series Installation and Programming Manual

Introduction

The AYC-Ex5/T65 series are integrated convertible readers and

controllers with a piezoelectric keypad. The units are vandal

resistant and water resistant, suitable for indoor or outdoor

mounting.
These units automatically determine whether to function as a

reader or as a controller. If the unit is connected to a standard

access control unit, then it functions as a reader. If the unit is

connected to a Rosslare secured intelligent power supply, it

functions as a secured controller.
As a controller, the units accept up to 500 users, and allow entry via

a personal identification number (PIN) and/or by presenting a

proximity card. The PIN code length for the controller has several

options. The PIN code length can be a set number of 4, 5, or 6 digits

or it can be a 4- to 8-digit code.
For information on how the unit functions as a reader, see

Chapter

For information on how the unit functions as a controller, see

Chapter

1.1

Reader/Controller Types

The different types of units described in this manual are:



Type E55 has PIN only



Types E65 and T65 have PIN and proximity card

Backlight Keypad Type Proximity

AYC-E55



Piezoelectric



AYC-E65B



Piezoelectric



AYC-E65BB



Piezoelectric



AYC-T65



Piezoelectric



Содержание AYC-E 5 Series


































































Результаты поиска

Содержание AYC-E 5 Series

Отзывы:

Похожие инструкции для AYC-E 5 Series

Бренды по названию

Популярные бренды

Rosslare AYC-E 5 Series, Инструкция по установке и программированию

Результаты поиска

Содержание AYC-E 5 Series

Отзывы:

Похожие инструкции для AYC-E 5 Series

Бренды по названию

Популярные бренды