Ross SRG-2200 Скачать руководство пользователя страница 19

Страница: 19 / 96

SRG-2200 User Guide (v6.0)

Physical Installation • 19

Connecting Power

The SRG-2200 operates from an externally su12V DC power source. A safety earth stud is provided for

earth bonding the chassis if you so require.
Your SRG-2200 includes 2 ex12V power supply block to provide you will full redundancy. Note that you

need to provide two power connections. For full power security, these should be on separate, independent and

secure power grids. However, you still gain the security of power supply failure redundancy if you use the same

power grid for both connections.

Connecting the Power Cable

Connect the power cable to the instrument first, and then connect it to the AC power source. Note that connecting a

live power cable causes the instrument to power on.

Replacing a Power Supply

Since DC power is provided from an external supply, if you need to replace a power supply, simply replace the

faulty external PSU.

Setting the Initial IP Address

The SRG-2200 is remotely controlled over an Ethernet link by a DashBoard client.
When using DashBoard to communicate with the SRG-2200, the SRG-2200 is always configured as a fixed IPv4

device using the Dashboard in conjunction with DIP switches

SW1

and

SW2

on the rear panel.

Configuring the DIP Switches

This section briefly summarizes the DIP Switch settings on the SRG-2200.

Figure 4.2

shows the DIP Switches in the

OFF

position.

Figure 4.2 DIP Switches on SRG-2200 Rear Panel

SW1

and

SW2

are used in conjunction with the DashBoard menus to set the IP Address of the card. Refer to

Table 4.1

and the rear panel labeling for DIP Switch positions.

Caution

— The SRG-2200 does not have a power switch.

Table 4.1 SW1 and SW2 Positions

SW1

Position

SW2

Position

Descriptions

OFF

The SRG-2200 network settings can be set by the user from

DashBoard (default).

OFF

No functionality.

OFF

The SRG-2200 IP Address is set to 192.168.2.1 The SRG-2200

Subnet Mask is set to 255.255.255.0.

The SRG-2200 IP Address is set to 10.1.2.1. The SRG-2200 Subnet

Mask is set to 255.255.255.0.

Содержание SRG-2200

































































































Результаты поиска

Содержание SRG-2200

Отзывы:

Бренды по названию

Популярные бренды

Ross SRG-2200, Руководство пользователя

Результаты поиска

Содержание SRG-2200

Отзывы:

Бренды по названию

Популярные бренды