Ross SRG-2200 Скачать руководство пользователя страница 18

Страница: 18 / 96

18 • Physical Installation

SRG-2200 User Guide (v6.0)

The SRG-2200 does not currently have an internal fan to assist with ventilation or cooling. Therefore, when you

install the unit in an equipment bay, it is imperative that you ensure there is sufficient space all around the unit to

allow the airflow to vent away any excess heat generated by the unit.

Rack Mount Installation

You can install the SRG-2200 into an equipment rack. It is recommended to use the rack mount kit and to loom the

cables so that they do not introduce extra weight or twisting force on the front panel rack mountings or rear panel

connectors. If installed in a mobile application, the rack mount kit is essential.
This section describes how to install the SRG-2200 into the rack.

Installing the SRG-2200 into a Rack Unit

The SRG-2200 mounts in the rack cabinet by means of four screws through the front mounting flanges. This should

normally be sufficient to carry the load, including weight of cables. Refer to the

SRG-2200 Quick Start Guide

for

mounting details.

Installing the Rear Support Brackets

In some cases, (mobile trucks, etc.) it may be desirable to also support the rear of the SRG-2200. The rear support

bars can be attached to the SRG-2200 in six possible positions. (

Figure 4.1

)

Figure 4.1 Installing the Support Brackets

To install the support brackets

1. Choose the position that suits the cabinet depth and will give approximately a 0.5” projection beyond the

previously mounted bracket. The frame support bars can work with racks up to 26” deep.

2. Using four screws per bracket, as shown in

Figure 4.1

, attach both bars.

3. Mount the frame to the front rails of the rack cabinet using rack screws.
4. At the rear of the cabinet, slide the bracket slots over the rear of the support bars and secure to the cabinet rear

rails with rack screws.

Caution

— The SRG-2200 could be damaged if it is powered on at temperatures or humidities outside

the specified ranges.

Warning

— Do not use the support brackets to carry the SRG-2200. The brackets are not primarily

designed for this purpose, and property damage or personal injury may result.

One Rack-Unit (1RU)

Mounting Frame

Side View

Rack Cabinet

Rear View

Cabinet

Front Vertical

Mounting Rail

Cabinet

Rear Vertical

Mounting Rail

Cabinet

Left Rear Vertical

Mounting Rail

Cabinet

Right Rear Vertical

Mounting Rail

0.500”

Rear Support Bar

Bracket

Allow approximately 0.500” of the end of the

Rear Support Bar to project beyond the Bracket

Select a mounting position

that allows Rear Support Bars

to slide into slots of Brackets

Содержание SRG-2200

































































































Результаты поиска

Содержание SRG-2200

Отзывы:

Бренды по названию

Популярные бренды

Ross SRG-2200, Руководство пользователя

Результаты поиска

Содержание SRG-2200

Отзывы:

Бренды по названию

Популярные бренды