background image

 

 

EMC Notices 

US FCC Part 15 

This equipment has been tested and found to comply with the limits for a class A Digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment. This 
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to cause harmful interference in which case  
users will be required to correct the interference at their own expense. 

 

 

 

Notice

 

Changes or modifications to this equipment not expressly approved by Ross Video 
Ltd. could void the user’s authority to operate this equipment. 

 CANADA 

This Class “A” digital apparatus complies with Canadian ICES-003.  

Cet appareil numerique de classe “A” est conforme à la norme NMB-003 du Canada. 

EUROPE 

This equipment is in compliance with the essential requirements and other relevant provisions of 

CE

 

Directive 93/68/EEC

INTERNATIONAL 

This equipment has been tested to 

CISPR 22:1997

 along with amendments 

A1:2000

 and 

A2:2002

 and 

found to comply with the limits for a Class A Digital device. 

 

 

 

Notice

 

This is a Class A product. In domestic environments this product may cause radio 
interference in which case the user may have to take adequate measures. 

 

Maintenance/User Serviceable Parts 

Routine maintenance to this RossGear product is not required. This product contains no user 
serviceable parts. If the module does not appear to be working properly, please contact Technical 
Support using the numbers listed under the “Contact Us” section on the last page of this manual.  All 
RossGear products are covered by a generous 5-year warranty and will be repaired without charge for 
materials or labor within this period.  See the “Warranty and Repair Policy” section in this manual for 
details.   

Содержание 8011A-7DR-004





























Отзывы: