Roshults 200360, Руководство пользователя

Страница: 7 / 16

7 / 16
21.01.13 5.1.4-R-UM-M-BBQ-G-X
EN
Module Gas Grill X
U S E R M A N UA L
1
2
3
4
5
6
7
Do not smoke while leak testing. Never leak test with an open flame.
Make a soap solution of one part liquid detergent and one part water.
You will need a spray bottle, brush, or rag to apply the solution to the
fittings. For the initial leak test, make sure the L.P. cylinder is full.
To test
Make sure all control valves are in the “OFF” position. Turn the gas
supply on. Check all connections from the L.P. cylinder up to and
including the connection to the manifold pipe assembly (the pipe that
goes to the burners).
Apply a soapy water mixture to the following (see numbers 1-7):
1. Cylinder.
2. The inlet end of the corrugated pipe is connected to the gas valve,
and the other end is connected with L type connector.
3. Gas valve.
4. The corrugated pipe outlet is connected gas valve.
5. The corrugated pipe outlet are aligned to the burner hole.
6. L type connector.
7. The reducing valve is connected to L type connector and other
end is connected the gas cylinder (clockwise).
Soap bubbles will appear where a leak is present. If a leak is present,
immediately turn off the gas supply, tighten any leaking fittings, turn
gas on, and recheck.
Should the gas continue to leak from any or all of the fittings, turn off
the gas supply, and contact our customer service at
+46 36 440 32 10.
Only those parts recommended by the manufacturer should be used
on the grill. Substitution will void the warranty. Do not use the grill
until all connections have been checked and do not leak.
Gas flow check:
Each grill burner is tested and adjusted at the factory prior to
shipment; however, variations in the local gas supply may make it
necessary to adjust the burners. The flames of the burners should be
visually checked.
Flames should be blue and stable with no yellow tips, excessive
noise or lifting. If any of these conditions exist, check to see if the
Secure that your gas grill is adapted for the intended use of gas and gas connection as specified in the technical data below:
Module Gas Grill X
Manufacturer
name address
Röshults Svenska Hantverk AB
Kärrviolsvägen 7, 554 75 Jönköping, Sweden
Gas Category I3 + (28-30/37) I3B/P(30) I3B/P(50) I3B/P(37) I2H I2E
Gas and
Supply
Pressure
G30 Butane at
28~30 mbar
G31 Propane at
37 mbar
G30 Butane and G31 Propane at
30mbar
G30 Butane and
G31 Propane at
50mbar
G30 Butane and
G31 Propane at
37mbar
Methane G20
20mbar
Methane G20
20mbar
Country Code BE, CH, CY, CZ,
ES, FR, GB, GR,
IE, IT, LT, LU, LV,
PT, SK, SI
BE, CY, DK, EE, FR, GB, HU, IT, LT,
NL, NO, SE, SI, SK, RO, HR, TR, BG,
IS, LU, MT, FI
AT, CH, DE, SK PL AT, CH, CZ, DK,
EE, ES, FI, FR,
GB, GR, HU, IE,
IT, LT, LV, NL,
NO, PT, RO, SE,
SI, SK
DE, LU, PL, RO
Burner 2 2 2 2 2 2
Nominal Heat
Input (single
burner)
4kW 4kW 4kW 4kW 4kW 4kW
Burner
Injector Size
0.96mm 0.96mm 0.88mm 0.91mm 1.52mm 1.52mm
Total Heat Input 8kW (G30:582g/h;G31:572g/h) (G20:0.76m3/h)
Service center Röshults Svenska Hantverk AB