Rosemount 3051S Series Скачать руководство пользователя страница 89

Страница: 89 / 190

Reference Manual

00809-0100-4803, Rev GA

Installation

September 2017

Installation

3.5.1

Rosemount 305 Integral Manifold installation procedure

To install a Rosemount 305 Integral Manifold to a Rosemount 3051SMV:

1. Inspect the PTFE SuperModule O-rings. If the O-rings are undamaged, reusing them is recommended.

If the O-rings are damaged (e.g. nicks), replace them with new O-rings.

Note

If replacing the O-rings, be careful not to scratch or deface the O-ring grooves or the surface of the
isolating diaphragm when removing the damaged O-rings.

2. Install the Integral manifold on the SuperModule process connection. Use the four manifold bolts for

alignment. Finger tighten the bolts, then tighten the bolts incrementally in a cross pattern to final
torque value. See

“Flange bolts” on page 71

for complete bolt installation information and torque

values. When fully tightened, the bolts should extend through the top of the SuperModule housing.

3. If the PTFE SuperModule O-rings have been replaced, the flange bolts should be re-tightened after

installation to compensate for seating of the O-rings.

4. If applicable, install flange adapters on the process end of the manifold using the 1.75-in. flange bolts

supplied with the transmitter.

3.5.2

Rosemount 304 Conventional Manifold installation procedure

To install a Rosemount 304 Conventional Manifold to a Rosemount 3051SMV:

1. Align the conventional manifold with the transmitter flange. Use the four manifold bolts for

alignment.

2. Finger tighten the bolts, then tighten the bolts incrementally in a cross pattern to final torque value.

See

“Flange bolts” on page 71

for complete bolt installation information and torque values. When

fully tightened, the bolts should extend through the top of the SuperModule assembly bolt hole but
must not contact the SuperModule housing.

3. If applicable, install flange adapters on the process end of the manifold using the 1.75-in. flange bolts

supplied with the transmitter.

3.5.3

Manifold operation

Always perform a zero trim on the transmitter/manifold assembly after installation to eliminate any shift
due to mounting effects. See

“Sensor trim overview” on page 90

Improper installation or operation of manifolds may result in process leaks, which may cause death or
serious injury.

Содержание 3051S Series































































































































































































Результаты поиска

Содержание 3051S Series

Отзывы:

Похожие инструкции для 3051S Series

Бренды по названию

Популярные бренды

Rosemount 3051S Series, Справочное руководство

Результаты поиска

Содержание 3051S Series

Отзывы:

Похожие инструкции для 3051S Series

Бренды по названию

Популярные бренды