Rosemount 3051S Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 190

background image

24

Reference Manual

00809-0100-4803, Rev GA

Configuration

September 2017

Configuration

2.5

Basic device configuration

This section provides procedures for configuring the basic requirements to commission the Rosemount
3051SMV. The

Basic Setup

tab, shown in

Figure 2-18 on page 25

, can be used to perform all of the

required transmitter configuration. The complete list of Field Communicator Fast Keys for basic setup are
shown in

Table 2-13 on page 62

Table 2-14 on page 63

.

Based on the configuration ordered, some measurements (i.e. static pressure, process temperature)
and/or calculation types (i.e. mass, volumetric, and energy flow) may not be available for all fluid types.
Available measurements and/or calculation types are determined by the multivariable type and
measurement type codes ordered. See

“Ordering information” on page 138

for more information.

All screens in this section are shown for multivariable type M (fully compensated mass and energy flow)
with measurement type 1 (differential pressure, static pressure, and process temperature). Field
Communicator Fast Keys are given for both multivariable type M and P (direct process variable output)
with measurement type 1. Field Communicator Fast Keys and screens for other multivariable types and
measurement types may vary.

Note

All screen shots in this section will be shown using AMS Device Manager. Engineering Assistant screens
are similar and the instructions shown here apply to both AMS Device Manager and Engineering
Assistant.

When using Engineering Assistant, a Reset Page button will be shown. In online mode, the

Reset Page

button will return all values on tab to the initial values received from the device before the start of the
configuration. If editing a previously saved configuration, the

Reset Page

button will return all values on

tab to those that were last saved. If starting a new configuration, all entered values on tab will be erased.

When information is edited on any AMS Device Manager tab, it will be highlighted in yellow. Edited
information is not sent to the transmitter until the

Apply

or

OK

button is selected.

Units of measure

If a unit of measure is edited and the

Apply

button is selected, the unit of measure will be changed in the

device memory and on screen, but the value may take up to 30 seconds to be updated on the AMS
Device Manager screen.

Mass and energy flow Fast Keys

1, 3

Direct process variable output Fast Keys

1, 3

«
...
30
31
32
33
34
...
»

Содержание 3051S Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3051S Series

DigitalFlow XMT868i

Бренд: Panametrics Страницы: 74

Бренд: FARMSCAN Страницы: 28

Бренд: Keithley Страницы: 138

Бренд: janitza Страницы: 12

Electone B-20CR

Бренд: Yamaha Страницы: 16

Бренд: Teledyne Analytical Instruments Страницы: 107

Бренд: horiba Страницы: 27

Бренд: TSI Instruments Страницы: 4

Бренд: SecureAlert, Inc. Страницы: 7

Бренд: GANN Страницы: 89

Бренд: Allen Organ Company Страницы: 29

Бренд: Biobase Страницы: 36

Бренд: HTC Страницы: 2

Бренд: DAKOTA ULTRASONICS Страницы: 51

Бренд: Fluke Страницы: 5

Бренд: PCE Health and Fitness Страницы: 4

Бренд: MFJ Страницы: 5

Optical Power Expert

Бренд: EXFO Страницы: 93

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды