manualshive.com logo in svg

Rosemount 1199, Справочное руководство

Поделиться
Скачать
Rosemount 1199 Скачать руководство пользователя страница 33

Reference Manual 

00809-0100-4002, Rev BB
November 2012

3-13

Rosemount 1199

HYGIENIC FLANGED 
TANK SPUD SEALS

Figure 3-20. EES 2-D Diagram

Figure 3-21. Hygienic Flanged 
Type Tank Spud Seal 3-D 
Diagram

Hygienic Approvals

Supplied 3-A approved hygienic seals are marked with a 3-A symbol.

Clamp Style Tank Spud 
(SSW)

For clamp style tank spud seals the procedures for welding the tank spud to 
the tank vessel are shipped with the tank spud. For the welding procedure 
refer to “Hygienic Tank Spud Welding Guidelines (SSW)” .

The clamp and O-ring are provided with the tank spud seal. Attach the clamp 
and hand-tighten the connection.

Flange Style Tank Spud 
(EES)

When connecting the process and mating flange, the bolts should be torqued 
to the specifications outlined by ANSI B16.5 or applicable flange 
requirements. 

HYGIENIC TANK SPUD 
WELDING GUIDELINES 
(SSW)

This guideline is intended to provide general guidance only to achieve an 
acceptable installation of a sanitary tank spud in order to mitigate potential 
costly rework. It will discuss ways to minimize potential distortion of the tank 
spud via tank preparation and welding practices. Employ a skilled, 
experienced welder to achieve best results.

Diaphragm

Instrument Connection

Mounting 
Flange

O-ring Groove

Diaphragm

O-Ring

Upper

Housing

Содержание 1199



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды