background image

5

Install Anti-Tip Bracket

Contact a qualified floor covering installer for the best procedure 
for drilling mounting holes through your type of floor covering.
Before moving range, slide range onto shipping base, cardboard 
or hardboard.

1. Remove template from the anti-tip bracket kit (found inside 

the oven cavity) or from the back page of this manual.

2. Place template on the floor in cabinet opening so that the left 

edge is against cabinet and top edge is against rear wall, 
molding or cabinet.

3. Tape template into place.
4. If countertop is not flush with cabinet opening edge, align 

template with overhang.

If cabinet opening is wider than that specified in the “Location 
Requirements” section, adjust template so range will be 
centered in cabinet opening.

5. To mount anti-tip bracket to wood floor, drill two 

¹⁄₈

" (3.2 mm) 

holes at the positions marked on the bracket template. 
Remove template from floor.

To mount anti-tip bracket to concrete or ceramic floor, use a 

³⁄₁₆

" (4.8 mm) masonry drill bit to drill 2 holes at the positions 

marked on the bracket template. Remove template from floor.

6. Tap plastic anchors into holes with a hammer.
7. Align anti-tip bracket holes with holes in floor. Fasten anti-tip 

bracket with screws provided.

Depending on the thickness of your flooring, longer screws 
may be necessary to anchor the bracket to the subfloor. 
Longer screws are available from your local hardware store.

8. Move range close to opening. Remove shipping base, 

cardboard or hardboard from under range. 

9. Connect power supply cord as described in the “Electrical 

Connection” section.

10. Move range into final position making sure rear leveling leg 

slides into anti-tip bracket.

11. Continue installing your range using the following the 

installation instructions.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death 
or serious burns to children and adults.

Содержание FEP310KW













Отзывы: