Installation Instructions for Hyper LED Mirror
RR.KH.LEDM.06.10
Roper Rhodes Ltd, Brassmill Lane Trading Estate, Bath, BA1 3JF
|
Tel: 01225 334148
|
waww.roperrhodes.co.uk
Please read carefully before you start and retain for future reference
Hyper
MLE370
2
2
2
2
OUTSIDE
ZONES
ZONE
2
ZONE
1
0.75m
2.25m
3.0m
0.6m
0.6m
0.6m
0.75m
IEE BATHROOM ZONES DIAGRAM
IMPORTANT
MIRROR LOCATION
SAFETY INSTRUCTIONS
(Applicable to UK Installations only)
All fittings must be installed by a competent person, in accordance
with current IEE wiring regulations. If in doubt, consult a qualified
electrician.
IMPORTANT
Always switch off the electrical supply at the mains during
installation and maintenance. It is recommended that the fuse is
withdrawn or the circuit breaker is switched off for the necessary
circuit before installation commences.
The product must be mounted a minimum of 150mm from an
adjacent wall or obstruction to ensure correct function of the
infrared sensor. The sensor can be repositioned if required. See
overleaf for details.
Fitting in Bathrooms is subject to the appropriate location (See
Diagram). Refer to IEE Regulations. This product is suitable for
Zones 2 and outside zones. It IS NOT suitable for installation in
Zone 0 or Zone 1. It is also not suitable for installation in Saunas,
Steam Rooms or Shower Cubicles.
This product is only suitable for permanent installation. DO NOT
connect to a trailing plug and socket outlet.
Although this product has an Ingress Protection rating of IP44, it is
only suitable for indoor use.
Do not attach the product to surfaces that are damp or otherwise
electrically conductive.
The product should be positioned well away from curtains and other
fabrics. Never cover the mirror.
Always ensure that the correct bulb is used and that the maximum
bulb rating is not exceeded.
This product is heated, we recommend that it is turned off after use
and should never be left on for prolonged periods of time.
CARE & SAFETY
REMEMBER
Wear suitable eye protection when drilling. Take care when using
power tools near water - the use of a residual current device (RCD)
is advised. Beware of hidden cables or pipes. Take care if drilling
on tiled surfaces in case the drill slips. A piece of masking tape
applied to the wall before marking out the fixing holes will stop the
drill from wandering.
WARNINGS
Do not strike glass components with hard or pointed items. Do not
place very hot or very cold items against or in close proximity to
glass surfaces unless an adequately thick insulation material is
used to prevent such items coming in contact with the glass.
The nominal thickness of the mirror glass used in this product is
8mm and is film backed for safety. If the glass becomes chipped or
broken, replace immediately. For details on replacement glass and
other components contact customer services at the address below.
THE MAXIMUM EVENLY DISTRIBUTED SHELF LOAD FOR THIS
PRODUCT IS 6KG. EXCEEDING THIS LOAD COULD BE DANGEROUS
AND MAY CAUSE DAMAGE TO THE PRODUCT. AVOID SHOCK
LOADING.
This product could be dangerous and installation is only to be
carried out by a competent person.
It is recommended that the unit is cleaned with a soft dry cloth
when turned off. Never use cleaning agents or abrasive materials
on any type of surface finish. Do not allow moisture to come into
contact with the lamp.
COMPLIANCE
This product complies with the following Electrical Safety
Standards:
EN 55015:2001; BS EN 60598-1: 2004, AMD:2001, AMD:2003; BS EN
60598-2-1: 1989. EN 60529: 1992 & A1, A2, A3.
REPLACING LED’S
In the unlikely event that the LED light strip should fail please
contact customer services for a replacement part at the address
shown.
WARNING
Disconnect the unit from the mains power supply before attempting
to replace a light strip. Remove the mirror glass from the body by
removing the screws and washers. Disconnect the heated mirror
pad and LED light strips and place the mirror face down on clean
soft surface.
The LED strips can be removed by sliding them along the mounting
plate, the replacement should then be pushed onto the mounting
plate until it clicks securely into place. Reconnect the the heated
pad and LED light strips. Reposition the mirror glass on the body
and secure with the screws and washers previously removed.
All fittings must be installed by a competent person, in
accordance with current IEE wiring regulations. If in doubt,
consult a qualified electrician.
150mm
Minimum distance
Infrared sensor
520mm
760mm
170mm
