ROPA Tiger 5 Скачать руководство пользователя | Manualshive

Страница: 53 / 530

background image

General Description

Function

53 / 530

4.1

Function

The machine is a self-propelled working machine for lifting sugar beets. The lifted

beets are collected in the bunker. When the bunker is filled up, the sugar beets may

either be deposited in a pile or directly loaded onto an accompanying vehicle using the

unloading conveyor.
An autopilot steers the Tiger on the field, so that intervention of the operator is rarely

required.
The lifting process is performed in several stages. The hydraulically adjustable defolia-

tor unit chops the beet leaf. Using a leaf worm conveyor and a rotating leaf-spreader,

the chopped beet leaves are spread onto the field over the desired width (not for

PISh).
Collecting leaves in accompanying transport vehicles is possible with a leaf recovery

unit (option for PBSh/PASh defoliators only).
The scalper has an automatic cutting depth control, which always ensures a precise

topping cut, no matter whether the beets are growing low in the ground or higher up.

The topping thickness may be adjusted from the driver's cabin.
The PR2 lifting unit may be moved to the right and left, to gain sufficient distance

between the front wheel and the subsequent row. The "Polder" shares on the linear

controlled share body are fitted with NON-STOP stone protection. Due to the con-

tra-rotating shaking movement of the shares, which may be switched on or off, the

sugar beets are lifted from the ground in an especially careful manner. The lifting

depth may be individually set for the left and right side from the driver's cabin.
The roller path may be optimally viewed from the driver's cabin. Due to its dimensions,

high performance with very good pre-cleaning is guaranteed. The infeed conveyor is

used to route the lifted sugar beets through the portal axle to the three strainer wheels

(turbines). In case of need, spring tines may be installed here. The cleaning effect and

the transport speed may easily be adjusted to the individual situation.
The ring elevator moves the beets upwards into the bunker. In the bunker, a worm

conveyor adjustable in height distributes the sugar beets evenly over the complete

space, so that maximum utilization of the loading capacity is possible. For this pur-

pose, the rotating direction (and therefore the feed direction) of the bunker auger is

reversed fully automated.
For unloading, the sugar beets are moved by the main tank conveyor and the cross

conveyor to the unloading conveyor and from there either deposited in a pile or loaded

onto an accompanying vehicle driving alongside.
All computers are networked via a CAN bus and supply all information to the driver on

the large capacity colour terminal R-Touch. All functions of the machine are controlled

and monitored by a single person from the driver's cabin.

«
...
51
52
53
54
55
...
»

Содержание Tiger 5



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger 5

Бренд: Fender Страницы: 15

Бренд: J D Squared Страницы: 18

Бренд: Raven Страницы: 27

Бренд: Raven Страницы: 79

Бренд: Raven Страницы: 88

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: Gainsborough Страницы: 2

Бренд: Rainbow Страницы: 18

Бренд: V.ORLANDI Страницы: 144

Бренд: A&D Страницы: 29

Бренд: Calibre Fitness Страницы: 11

mocon AQUATRAN 3/38

Бренд: Ametek Страницы: 85

Pro hunter 2525

Бренд: SprotDog Страницы: 28

Бренд: Barikell Страницы: 32

Бренд: v.link Страницы: 20

Бренд: BCP Страницы: 8

Бренд: Mindray Страницы: 295

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды