RONDELL RDE-1251, Инструкция по эксплуатации

Страница: 5 / 20

5
ENGLISH
•
Clean the motor unit (7) with a soft, slightly damp cloth
and then wipe it dry.
•
Do not immerse the motor unit (7) into any liquids and do not
wash it with water.
•
Place the blender on a flat stable surface.
ATTENTION! Continuous operation time of the blender should
not exceed 60 seconds, and the break between operations
should be 1-2 minutes.
•
Do not remove the blender bowl (3) and the bowl lid (2) during
the operation.
USING THE BLENDER
The blender is used for chopping products, mixing various ingre-
dients and making cocktails.
•
Install the blender bowl (3) on the motor unit (7), the bowl
(3) handle (4) must be situated on the right or left side of the
motor unit (7), turn the bowl (3) clockwise until bumping.
•
Remove the blender bowl lid (2).
•
Put the necessary ingredients into the bowl (3).
Note: Maximal capacity of the glass bowl (3) is 1500 ml. To avoid
possible foam forming or spilling during processing of foamy liq-
uids or low-density liquids, such as milk, do not exceed the mark
1000 ml on the pitcher.
•
Cover the blender bowl (3) with the lid (2), insert the mea-
suring cup (1) into the lid (2) opening and turn it clockwise
until bumping.
•
Make sure once again that the blender bowl (3) is installed
correctly.
•
Insert the power plug into the mains socket.
Note: The blender will not be switched on if the blender bowl (3)
is installed incorrectly.
•
Use the operation mode switch (8) to set the required rotation
speed of the knives:
«1» (low speed) - for mixing liquid products.
«2» (high speed) - for liquid and hard products.
«P» - pulse mode.
•
To switch the pulse mode on, set the switch (8) to the posi-
tion “P” and hold it.
•
During the operation or between the operation cycles, you
can add the required ingredients into the bowl (3). To do this,
remove the measuring cup (1) turning it counterclockwise, you
can use the measuring cup (1) as a bowl for adding necessary
liquid ingredients. After adding the ingredients, place the cup
(1) back to its place and turn it clockwise until bumping.
•
After the unit’s operation is finished, set the operation mode
switch (8) to the “0” position and unplug the unit.
•
Remove the blender bowl (3) from the motor unit (7) by turning
it counterclockwise until bumping.
•
Remove the lid (2) from the bowl (3) and take the processed
products out of the bowl (3).
•
After the operation is finished, wash the blender bowl (3).
Note: If food processing is hindered, add some liquid (water,
liquor, juice) into the blender bowl (3).
•
Before starting to chop/mix, we recommend to peel fruit,
remove inedible parts, such as stones, and cut fruit into
2х2 cm cubes.
ATTENTION! Continuous operation time of the blender should
not exceed 60 seconds, and the break between operations
should be 1-2 minutes.
CLEANING AND MAINTENANCE
After the unit operation is finished, switch the blender off by set-
ting the operation mode switch (8) to the “0” position and unplug it.
•
Remove the blender bowl (3) from the motor unit (7) by turning
it counterclockwise until bumping.
•
Remove the lid (2) and take the processed products out of
the bowl (3).
•
Wash the bowl (3) preliminarily.
•
Remove the knife block (6) and the sealing gasket (5). To
remove the knife block (6) turn it counterclockwise and
remove.
WARNING: The knife block (6) cutting edges are very sharp and
dangerous. Handle the knife block very carefully.
•
Wash the knife block (6) only from the knives side, do not
immerse the knife block (6) into water or other liquids.
•
Wash the bowl (3), the sealing gasket (5), the lid (2) and the
measuring cup (1) with warm water and soft detergent and
dry them.
•
You can wash the blender bowl (3) in a dishwashing machine
after removing the knife block (6).
•
Clean the motor unit (7) with a soft, slightly damp cloth and
then wipe it dry.
•
Do not use coarse sponges, abrasives and solvents to clean
the blender.
•
Do not immerse the blender motor unit (7) into any liq-
uids; do not wash it in a dishwashing machine.
•
Install the sealing gasket (5) into the knife block (6).
•
Install the knife block (6) into the blender bowl (3) and thread
it rotating clockwise.
•
To avoid damage of the sealing gasket (5) when installing the
knife block (6), do not apply excessive effort.
STORAGE
•
Follow the requirements of the “CLEANING AND CARE” sec-
tion before taking the unit away for storage.
•
Keep the unit in a dry clean place out of reach of children and
disabled persons.
IM RDE-1251.indd 5 7/7/21 9:57 AM