CONNECTION
Connect the AC cord to a properly grounded ac outlet.
Determine which input configuration you will use; either discreet right/left, TRS
stereo, or mono.
For a discreet right/left input configuration, connect a balanced XLR plug contain-
ing the “Right” portion of the stereo signal to the Right Main Input. Connect a
balanced XLR plug containing the “Left” portion of the stereo signal to the Left
Input.
For a TRS stereo input configuration, connect a Tip-Ring-Sleeve stereo plug into
the front panel STEREO IN input. This cable may come from a mixer’s headphone
output for example.
The Aux Inputs are connected in the same manner as the discreet right/left input
configuration listed above.
To send a mono signal to the RA62b, connect an XLR jack to either Main Input, or
a single 1/4” Tip-Sleeve or RCA plug into either Aux Input input and press in the
front panel MONO/STEREO switch. This mono signal will be fed to both the right
and left sides of the headphone outputs.
INSERTS
The inserts have been provided so you can directly access each headphone
output with its own program material.
The inserts
require Tip-Ring-Sleeve connectors, with right and left signals on the
tip and ring respectively. If you use a TS mono plug - you will only hear sound out
of one side.
When these insert jacks are used, the main Right/Stereo and Left/Mono, as well
as the Aux Inputs - are disconnected. Only the stereo signals sent to the Insert
jacks go to that corresponding output.
CAUTION: Plugging a mono 1/4” TS plug into the Headphone
Outputs may cause permanent damage to the unit because
one side would be shorted to ground.
NEVER PLUG A MONO
PLUG INTO ANY OF THE HEADPHONE OUTPUTS.
3
4
Tip
Ring
Sleeve
(ground)
DESCRIPTION
FRONT PANEL
MONO
STEREO
pwr
STEREO
INPUT
PAN
L R
6 CHANNEL
HEADPHONE AMPLIFIER
OUTPUT
LEVEL
LEVEL
OUTPUT
LEVEL
LEVEL
OUTPUT
LEVEL
LEVEL
OUTPUT
LEVEL
LEVEL
OUTPUT
LEVEL
LEVEL
OUTPUT
LEVEL
LEVEL
RA62b
Note: Descriptions for Channel One through Channel Six are identical.
OUT 1 - 6 : 1/4” and 1/8” (3.5 mm) Tip-Ring-Sleeve jacks for connection to a
standard pair of headphones or earphones. These jacks may be used simulta-
neously.
VOLUME 1 - 6: Controls the amount of output signal from the indicated channel.
MONO/STEREO SWITCH: When this switch is pressed in, the Right and Left
channels are summed together providing a mono output signal.
PAN: Controls the relative amount of signal sent to the Right and Left output
channels.
STEREO IN: 1/4” TRS input jack which parallels the rear panel Right and Left
input jacks.
POWER LED: Indicates that the RA62 is connected to the power supply and is
on.
REAR PANEL
INSERT 6
INSERT 5
INSERT 4
INSERT 3
INSERT 2
INSERT 1
RIGHT
LEFT
RIGHT
LEFT
120 VAC
50/60 Hz 15 VA
MADE IN U.S.A.
RISQUE DE CHOC - NE PAS ENLEVER
SERIAL NUMBER
MODEL RA62b
62-
WARNING:
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK.
NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
MAIN INPUTS
AUX INPUTS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
LEFT
RIGHT
120 VAC INPUT: Connects to a properly grounded AC outlet.
MAIN INPUTS: Balanced XLR jacks for connecting to the desired Right and Left
program material.
AUX INPUTS: 1/4” and RCA unbalanced inputs - for use in the event additional
program material is to be mixed with the main inputs, or if XLR plugs are not
available.
Note: The description for the Channel Inserts pertains to all six channels.
CHANNEL INSERTS: 1/4” TRS jacks which directly access the channel’s
heaphone output circuitry. This is a stereo jack and requires a TRS stereo signal.
