Safety information
Important information
1. Please remember that the natural playfulness and
temperament of children may result in unforeseeable
situations and dangers, for which the manufacturer
cannot be held responsible. You should therefore instruct
the children or users of how to use the BMW Vehicle
correctly, draw their attention to the possible
dangers and keep children under supervision at all times.
2. BMW AG cannot accept any liability for accidents of any
kind that are the user's own fault or resulting from the
user's failure to adhere to the following warning instructions.
3. The BMW Vehicle is not approved for road use.
4. It should therefore not be used on public roads, paths or the
like.
5. Children must wear closed shoes. Not to be used in traffic.
6. The BMW Vehicle should not be used near stairs or
sloping land.
7. Nearby stairs must be secured to ensure that they do not
present any danger to the children.
8. The BMW Vehicle should not be used on icy or slippery
ground.
9. Do not store the BMW Vehicle close to heat sources.
10. The BMW Vehicle should not be used in water.
11. The BMW Vehicle is only designed to carry a single
child.
12. Do not attach it to other vehicles.
13. The rider should always wear a helmet that is properly
fastened .
14. The BMW Vehicle is only suitable for children between
3 and 5years of age.
15. The maximum payload of the vehicle is 22kg.
16. Store the BMW Vehicle in a secure location. Do not
leave it outside overnight.
17. Keep small parts that can be swallowed and plastic bags out
of the reach of children. Danger of suffocation.
18. Before starting assembly, check that all parts are present. If
any parts are missing, please contact the dealer from which
you purchased the vehicle.
19. Keep the incompletely assembled vehicle out of the reach of
children since it may contain sharp edges, pointed corners
and small parts.
20. Please retain all packaging for further information. This toy is
not suitable for children under 3 years of age due to small
parts.
21. Do not activate the vehicle unless you are seated and in a safe,
outdoor environment suitable for riding. There are additional
hazards of using the toy in areas other than private grounds.
22. The toy shall be used with caution since skill is required to
avoid falls or collisions causing injury to the user and third
parties. Continuous adult supervision required; never use
near motor vehicles; never use near streets, swimming pools,
hills, steps, or sloped driveways.
23. Adult Assembly required.
24. Never allow more than one rider.
Care and maintenance
The wheel bushings and drive shaft should be
lubricated with a few drops of oil four times a
year.
Check all the parts at regular intervals for signs of
wear. Check the screw connections for a secure
fit. To maintain the high safety level, worn parts
must be replaced immediately and the vehicle
not used until it has been repaired.
You can obtain spare parts from Hunter products.
WARNING
Assembly
1.Assemble Rear Wheel:(fig1)
Insert the rear wheel axle into the chassis and insert the left
rear wheel, washer, hexagon nut into the rear axle in the order
shown. Then, cover the rear wheel hubcap. Follow the same
procedures to assemble the right rear wheel.
2.Assemble Pedal Component:(fig2)
Connect the left side pedal into the left square hole of the front
wheel and insert the right side pedal into the right square hole
of the front wheel.
3.Assemble front fork:(fig3)
Insert the right and left leg of front fork (the mudguard should
face forward) into the connected hole ,please pay attention that
the hole of two sides must be in alignment. Use ST4.2*29
self tapping screw to tighten the connecting part and hole
closely(the tighten torque is 1.5 N-m),and then fix the mudguard
and front fork connecting part with ST3.2*13 self tapping screw
for fastening. (the tighten torque is 1.5N-m).
4.Assemble front wheel component:(fig4)
Insert the stand pipe of front fork (the mudguard should face
forward) into the fixing hole in front of the chassis.
5.Assemble handle bar:(fig5)
Remove the M5*28 screw from the handle bar component first
and insert the stand pipe of the handle bar into the stand
pipe(pay attention to the assemble direction of the handle bar),
use M5*28 screw for fastening(the tighten torque is 2.5N-m).
6.Using the seat:(fig6)
Rotate the button on the seat to the open position, the seat can
be upturned and the following space under the seat also can be
used as a storage box.
