1.
Fold the snare.
Loosen the hand knob and raise it to the highest position; then
use a drum key to loosen the bolt and put the snare in a vertical
position.
When the position is correct, tighten the hand knob fi rmly.
2.
Fold the drum sound module.
Use a drum key to loosen the
bolts of the drum sound module
and sound module mount, and
fold the drum sound module to a
vertical position.
When the position is correct,
tighten the bolt fi rmly.
Loosen the hand knob and
rotate the sound module mount
from inside, lowering it to the
lowest position as shown in the
illustration.
* Leave the hand knob loose.
3.
Fold the hi-hat.
Use the included drum key to loosen the hi-
hat arm bolt, and rotate it so that the hi-hat
is vertical.
When the position is correct, tighten the
bolt fi rmly.
Loosen the hand knob, and rotate the pipe
from the outside to fold it.
Position the hi-hat so that it faces the
center of the snare pipe.
* Leave the hand knob loose.
1
2
3
4.
Fold tom 1.
Use the drum key to loosen the tom bolt, and position it vertically.
When the position is correct, tighten the bolt fi rmly.
5.
Lower the pipe while aligning the arm to the position of
the stand’s angular pipe.
* Take care not to pinch the cable when lowering the pipe.
NOTE
Loosen the hand knob, and lower
it all the way down.
When it is fully lowered, fi rmly
tighten the hand knob and
the hi-hat hand knob that you
loosened.
Angular pipe
6.
Fold the cymbal rod and lower it.
Use a drum key to loosen the cymbal rod bolt, and fold the
cymbal.
After folding it, securely tighten the bolt.
Open the pipe lever, and rotate the cymbal rod to slowly lower it
so that you can see the back of the cymbal.
After lowering the rod, securely tighten the lever.
Release the lever and lower
the cymbal rod.
Fold up the cymbal rods.
Rotate the cymbal rod to lower it so that
you can see the back of the cymbal.
By rotating the cymbal rod you can
fold the stand more compactly.
7.
Fold the snare.
Loosen the hand knob to align the snare with the orientation of
the tom, and then lower the snare until the pad mount touches.
* Lower the snare so that the hi-hat is between the snare arm
and the snare.
When the position is correct, securely tighten the hand knob.
3
1
4
2
1.
Turn off the power.
2.
Disconnect all cables from the drum sound module.
Disconnect the connection cable, AC adaptor, and cables
connected to the OUTPUT/PHONES jacks.
Loosen the knobs that
fasten the connection
cable, and pull the
connector straight
out.
3.
Disconnect the hi-hat control pedal cable.
You can fasten the
disconnected cable
to the cable holder.
4.
Remove the kick pedal.
1.
Loosen the hand knob, and rotate the kick pedal
attachment plate toward the inside with the kick pad
outside.
When the position is correct, securely tighten the hand knob.
2.
Rotate tom 3 and fold it.
Loosen the tom knob, and rotate it from the outside.
Use a drum key to loosen the tom bolt, position the tom vertically,
and move it to the end of the tom arm.
1
2
3
Loosen the hand knob and rotate
the tom arm from the outside to
lower it all the way down.
* Leave the hand knob loose.
3.
Fold tom 2.
Use a drum key to loosen the tom bolt, and position the tom
vertically.
4.
Lower the pipe while aligning the arm to the position of
the stand’s angular pipe.
Loosen the hand knob, and lower it all the way down.
By loosening the tom’s knob and
angling it, you can lower the pipe all
the way down.
Angular pipe
After lowering it all the way down, securely tighten the pipe’s
hand knob and the hand knob of tom 3 that you left loosened.
* Take care not to pinch the cable when lowering the pipe.
NOTE
5.
Fold the cymbal rod and lower it.
Use a drum key to loosen the cymbal rod bolt, and fold the
cymbal.
After folding it, securely tighten the bolt.
Open the pipe lever, and rotate the cymbal rod to slowly lower it
so that you can see the back of the cymbal.
After lowering the rod, securely tighten the lever.
Rotate the cymbal rod to lower it so that
you can see the back of the cymbal.
By rotating the cymbal rod you can
fold the stand more compactly.
Release the lever and lower
the cymbal rod.
Fold up the cymbal rods.
1.
Fold the sound module mount.
Loosen the hand knob, and fold the sound module mount inward.
When the position is correct, securely tighten the hand knob.
2.
Loosen the hand knob and fold the stand inwards.
Not less than 13 cm
* When storing the system in a
folded state, leave the stand’s
pipes opened so that they are at
least 13 cm apart. If this distance is
less than 13 cm, the stand will be
unstable and may fall over.
NOTE
Disconnect the cables and pedals
Fold the left side
Folding the right side
Folding the stand.
MEMO
For easy transportation, you can place the
system in a carrying case (CB-TDP; sold
separately) designed specifi cally for the
Roland V-Drums Portable.
NOTE
* Take care not to allow the system to tip over when folding it up.
* When setting up or storing the stand, please be careful not to get your fi ngers pinched
between the movable part and the unit. In places where small children are present, make
sure that an adult provides supervision and guidance.
Setup Guide
Folding for Storage /
Extending for Use
Before using this product, please carefully read “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (the leafl et “USING THE UNIT SAFELY” and the “Owner’s
Manual”), as well as the notes in the Setup Guide in order to ensure that you use the
product correctly. After reading, keep the document(s) where it will be available for
immediate reference.
© 2016 ROLAND CORPORATION
Watch the Quick Start Video
This video explains how to use the TD-1KPX.
http://roland.cm/td-1kpx
Folding for Storage
1
2
3
1.
Extend the stand.
Loosen the hand knob, and open to 90 degrees.
After you’ve opened the stand,
tighten the hand knob.
Do not open wider than 90 degrees
2.
Open the sound module mount.
Loosen the hand knob, and
open the sound module
mount.
* Leave the hand knob loose.
3.
Raise the snare, and position it at the front.
Loosen the hand knob, then raise the snare all the way and
position it at the front.
When the position is correct, securely tighten the hand knob.
4.
Raise and set up the cymbal rods.
Release the lever and pull
out the cymbal rod.
Tilt up the cymbal rod.
5.
Raise tom 2.
Use a drum key to loosen
the tom’s bolt, and raise
tom 2.
6.
Extend the pipe, and position tom 2 at the front.
Loosen the hand knob of tom 3 before you
extend the pipe.
Loosen the hand knob of the pipe, and
extend it.
When the position is correct, securely tighten
the hand knob of the pipe to fasten it.
For the height of tom 2, refer to “
3
Extending the pipe” in the section on
assembly.
* Leave the hand knob of tom 3 loose.
* Take care that the cables are not excessively stretched.
NOTE
7.
Raise tom 3.
1
Rotate the tom arm from the
outside.
Adjust the height of the tom.
Tighten the hand knob to secure
the tom arm.
2
Use a drum key to
loosen the tom’s bolt,
then raise the tom and
adjust its position.
Loosen the tom’s knob
and rotate it from the
outside.
3
8.
Rotate the kick pad and the pedal plate.
Loosen the hand knobs, and adjust
the position of the kick pad and
the pedal plate.
Tighten the hand knobs to secure
the kick pad and the pedal plate
position.
1.
Raise and set up the cymbal rods.
Release the lever and pull
out the cymbal rod.
Tilt up the cymbal rod.
2.
Extend the pipe so that tom 1 is in the front.
Loosen the hand knob of the hi-hat,
and then loosen the hand knob of
the pipe and extend it.
When the position is correct, tighten
the hand knob of the pipe to secure
it.
* Leave the hand knob of the hi-
hat loose.
* Take care that the cables are not
excessively stretched.
NOTE
3.
Raise tom 1.
Use a drum key to loosen the bolt of the tom, and then raise it.
When the tom is positioned correctly, tighten the bolt to secure
the tom.
4.
Raise the hi-hat.
Rotate the hi-hat arm.
Adjust the height of the hi-hat.
When the position is correct, tighten
the hand knob to secure it.
Use a drum key to loosen the bolt of the
hi-hat arm, and raise the hi-hat.
When the position is correct, tighten the
bolt to secure it.
1
2
3
5.
Raise the drum sound module.
Use a drum key to loosen the
bolts of the drum sound module
and the sound module mount,
and raise the drum sound
module.
When the position is correct,
tighten the bolts securely.
Rotate the sound module mount
from the inside, placing it in the
position shown in the illustration.
When the position is correct,
securely tighten the hand knob.
6.
Connect the cable to the drum sound module.
Connect the connection cable to the drum sound module as
shown in the illustration. Insert the connector all the way, and turn
the knobs to secure the connector.
1.
Raise the snare and adjust its height.
Use a drum key to loosen the bolt, raise the snare, and loosen the
hand knob to adjust the height.
When the position is correct, tighten the bolt and the hand knob
securely.
2.
Kick pedal positioning.
Mount the kick pedal to the pedal plate and so that the beater
strikes the center of the kick pad.
Beater
Install the kick pedal
securely.
For details, refer to “
9
Attaching the kick” in the section on
assembly.
3.
Position the hi-hat control pedal directly below the hi-
hat.
4.
Connect the cable (HHC) to the hi-hat control pedal.
HHC
5.
Check the cable connections.
For details, refer to “
11
Connecting the cables” in the section on
assembly.
6.
Connect the AC adaptor and speakers.
For details, refer to “
12
Connect the AC adaptor and speakers”
in the section on assembly.
Opening the right side
Opening the left side
Position the snare and pedals
4
Adjust the position and angle of the pads
1.
Adjust the position and angle of each pad as shown in the illustration.
* Take care not to allow the system to tip over when setting it up.
* When setting up or storing the stand, please be careful not to get your fi ngers
pinched between the movable part and the unit. In places where small children are
present, make sure that an adult provides supervision and guidance.
NOTE
NOTE
* Before every performance, check to make sure that none of the bolts or hand knobs are loose. Otherwise, if left untightened, it can be quite
dangerous, since the stand could fall over during a performance, or a pad could come off .
Extending for Use
* To prevent damage to your fl oor or carpet, and to ensure a stable setup, we recommend that you use a separately sold drum mat (TDM
series).
You can attach your
drum key to the cable
holder.
Cable holder
Tilt it forward slightly.
Position so there is 12–15 cm
(4-3/4”–6”) of space between
the snare and tom.
The hi-hat should be placed
about 20 cm (7-7/8”) higher
than the snare.
Place directly
below the hi-hat.
The snare and
tom 3 should
be at the same
height.
Allow for 3–6 cm
(1-3/16”–2-3/8”) of
space between tom
1 and tom 2.
Place at a slightly
lower position than
the crash cymbal.
Adjust the angles so that you
can perform comfortably.
The tom 1 and tom 2
should be at the same
height.
