background image

- 3 - 

TABLE OF CONTENTS 

Introduction and Definitions of Safety Warnings 

Safety Warnings – Risk of Asphyxiation, Bursting,  Electrocution,  
            Shock, Explosion or Fire 

Safety Warnings – Risk of Moving Parts, Burns, Injury from Lifting,  
            Propelled Objects, Unsafe Operation and Damage to  
            Compressor or Property 

Identification of System Controls 

6-7 

Pre-Start Checklist 

7-8 

Specifications  

Operation 9 
Maintenance 9-10 
Troubleshooting 10 
Guarantee 11 
Schematics – JC10 

12-13 

                      JC13 

14-15 

 

INTRODUCTION 

Congratulations on the purchase of your new ROLAIR

®

 air compressor!   

 
With over 50 years experience building ROLAIR

®

 air compressors specifically designed for the professional, 

Associate Engineering Corporation has earned a reputation for providing a product unsurpassed in quality 
and reliability.  We are committed to continuing this tradition by analyzing and adapting to the changing 
needs and rigorous demands of your industry.  You can depend on ROLAIR

®

 because they are built to last.   

 
This manual was compiled for the benefit of the operator.  Do not use or allow anyone else to use your air 
compressor until this manual is read and all safety/operating instructions are understood.  By reading and 
following the instructions contained in this manual, you can achieve years of trouble free service from your 
new air compressor.  If you have any additional safety or operating questions after reading this manual, 
please contact your distributor or our customer service department.  Do not remove or paint over any of 
the warning decals attached to the compressor. 
 

Definitions – Safety Warnings 

Safety symbols are used throughout this manual to alert you to potentially hazardous situations.  The 
following definitions describe the level of severity for each signal word. 
 

  DANGER: 

Indicates an imminently hazardous situation which, if not avoided, WILL result in death 

 

 

or serious injury. 

 

  WARNING: 

Indicates a potentially hazardous situation which, if not avoided,  COULD result in  

 

 

death or serious injury. 

 

  CAUTION: 

Indicates a potentially hazardous situation which, if not avoided,  MAY result in minor  

 

 

or moderate injury or damage to the air compressor. 

 

 

Содержание JC10
















Отзывы: