manualshive.com logo in svg

rojaflex MLL-80 NHK, Оригинальная инструкция по сборке и эксплуатации

Поделиться
Скачать
rojaflex MLL-80 NHK Скачать руководство пользователя страница 3

 

www.rojaflex.com

    

  

3

Important safety instructions!

For the safety of persons it is impor-

tant to follow these instructions!

Please keep the manual and hand it over 
to the new owner in case of change of 
ownership!
This device can be used by children 8 
years of age and by persons with with 
reduced physical, sensory or mental abili-
ties or lack of experience and experience 
and knowledge if they are supervised or 
instructed instructed in the safe use of 
the use of the device, and understand 
the hazards involved understand.
Children are not allowed to play with the 
device.
Cleaning and maintenance by the user 
must not be carried out by children wit-
hout supervision.

WARNING!

The motor must be disconnected from its 
power source during cleaning, mainte-
nance and parts replacement.
After unpacking, compare the motor 
type with the corresponding information 
on the nameplate.
Incomplete devices or devices that do 
not comply with the specifications must 
not be put into operation.

WARNING!
Non-observance may result in danger 

to life!

There is a danger to life from electric 
shock when working on electrical equip-
ment!
The mains connection of the motor and 
all work on electrical installations may 
only be carried out by an authorized 
electrician in accordance with the con-
nection diagrams in this manual.

Carry out all assembly and connection 
work in a de-energized state.
When using the device in damp rooms, 
observe the regulations for installation 
in damp rooms, especially DIN VDE 0100, 
Parts 701 and 702.
Observe the protective measures 
protective measures contained in these 
regulations.
The use of defective devices can endan-
germent of persons and damage to 
damage to property (electric shock, short 
circuit).
Never use defective or damaged dama-
ged devices.
Check the motor and power cord for 
intactness.

Please contact our Service (see last 

page for contact) if you notice any da-

mage to the device.

ATTENTION!

Notes on installation and connection 

must be observed!

Improper installation and assembly 

can lead to serious injuries!

Lay the power cable of the motor in-
ternally in the empty conduit up to the 
junction box, observing the local electri-
cal regulations.
Mains cables must not be laid in the 
winding space of the plant. Make sure 
that the power cable does not come into 
contact with moving parts of the plant.

General safety instructions

Содержание MLL-80 NHK





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды