manualshive.com logo in svg

ROHS MC9S08QE128, Справочное руководство

ROHS MC9S08QE128 - это продукт высочайшего качества, который обеспечивает надежное и эффективное функционирование вашего устройства. Вы можете скачать бесплатно Reference Manual и другие руководства по эксплуатации на manualshive.com. Познакомьтесь с функционалом этого устройства и улучшите свой опыт использования с помощью нашего руководства.

Поделиться
Скачать
background image

Chapter 5 Resets, Interrupts, and General System Control

MC9S08QE128 MCU Series Reference Manual, Rev. 2

Freescale Semiconductor

91

When the 1-kHz clock source is selected, the COP counter is re-initialized to zero upon entry to stop mode.
The COP counter begins from zero after the MCU exits stop mode.

5.5

Interrupts

Interrupts provide a way to save the current CPU status and registers, execute an interrupt service routine
(ISR), and then restore the CPU status so processing resumes where it left off before the interrupt. Other
than the software interrupt (SWI), which is a program instruction, interrupts are caused by hardware events
such as an edge on the IRQ pin or a timer-overflow event. The debug module can also generate an SWI
under certain circumstances.

If an event occurs in an enabled interrupt source, an associated read-only status flag will become set. The
CPU will not respond unless the local interrupt enable is a 1 to enable the interrupt and the I bit in the CCR
is 0 to allow interrupts. The global interrupt mask (I bit) in the CCR is initially set after reset which
prevents all maskable interrupt sources. The user program initializes the stack pointer and performs other
system setup before clearing the I bit to allow the CPU to respond to interrupts.

When the CPU receives a qualified interrupt request, it completes the current instruction before responding
to the interrupt. The interrupt sequence obeys the same cycle-by-cycle sequence as the SWI instruction and
consists of:

•

Saving the CPU registers on the stack

•

Setting the I bit in the CCR to mask further interrupts

•

Fetching the interrupt vector for the highest-priority interrupt that is currently pending

•

Filling the instruction queue with the first three bytes of program information starting from the
address fetched from the interrupt vector locations

While the CPU is responding to the interrupt, the I bit is automatically set to avoid the possibility of another
interrupt interrupting the ISR itself (this is called nesting of interrupts). Normally, the I bit is restored to 0
when the CCR is restored from the value stacked on entry to the ISR. In rare cases, the I bit can be cleared
inside an ISR (after clearing the status flag that generated the interrupt) so that other interrupts can be
serviced without waiting for the first service routine to finish. This practice is not recommended for anyone
other than the most experienced programmers because it can lead to subtle program errors that are difficult
to debug.

NOTE

In order for the ISR to be available in the memory map regardless of the
PPAGE value, ISRs should be located in pages 0, 1, or 3.

The interrupt service routine ends with a return-from-interrupt (RTI) instruction which restores the CCR,
A, X, and PC registers to their pre-interrupt values by reading the previously saved information from the
stack.

NOTE

For compatibility with M68HC08 devices, the H register is not
automatically saved and restored. It is good programming practice to push
H onto the stack at the start of the interrupt service routine (ISR) and restore
it immediately before the RTI that is used to return from the ISR.

Exclude: 2

Содержание MC9S08QE128


























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MC9S08QE128

ABB 650 series Engineering Manual preview
650 series
Бренд: ABB Страницы: 128
ABB ControlMaster CM15 Instructions preview
ControlMaster CM15
Бренд: ABB Страницы: 4
Data Aire dap4 touch Protocol Manual preview
dap4 touch
Бренд: Data Aire Страницы: 13
Hach SC4200c User Manual preview
SC4200c
Бренд: Hach Страницы: 36
Elby Designs ASM301-ADSR Diagrams preview
ASM301-ADSR
Бренд: Elby Designs Страницы: 4
HomeMatic HmIP-FAL230-C10 Installation And Operaion Manual preview
HmIP-FAL230-C10
Бренд: HomeMatic Страницы: 42
Sutter Instrument TRIO MPC-165 Series Operation Manual preview
TRIO MPC-165 Series
Бренд: Sutter Instrument Страницы: 60
Phoenix Contact 2297031 Manual preview
2297031
Бренд: Phoenix Contact Страницы: 56
Watlow EZ-ZONE PM L AAAAB Series User Manual preview
EZ-ZONE PM L AAAAB Series
Бренд: Watlow Страницы: 30
Invacare MK5 NX w/ACC Service Manual preview
MK5 NX w/ACC
Бренд: Invacare Страницы: 44
Roth Touchline PL 2 Ch Installation Manual preview
Touchline PL 2 Ch
Бренд: Roth Страницы: 8
Instruments of Things IO-Lights User Manual preview
IO-Lights
Бренд: Instruments of Things Страницы: 12
Delta Regis BECT832-SSO Operation Manual preview
BECT832-SSO
Бренд: Delta Regis Страницы: 15
Texas Instruments Chipcon Products CC1110DK Quick Start Instructions preview
Chipcon Products CC1110DK
Бренд: Texas Instruments Страницы: 3
Dataprobe iPIO-16 Quick Start Manual preview
iPIO-16
Бренд: Dataprobe Страницы: 2
V2 AYROS 1000D 24V-120V Manual preview
AYROS 1000D 24V-120V
Бренд: V2 Страницы: 116
Carrera GO!!! Plus Operating Instructions preview
GO!!! Plus
Бренд: Carrera Страницы: 3
Whelen Engineering Company MPC03 Installation & Operating Manual preview
MPC03
Бренд: Whelen Engineering Company Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды