4
Consult your local ROHL showroom for additional information and specifications. For complete warranty details and a list of showrooms, go to www.rohlhome.com.
www.rohlhome.com
Installation Instructions
9.18245*
9.13501
9.01456/Hot*
9.01456/Cold*
9.30237
9.18235*
9.13501/Left
9.13500/Right
9.12456*
9.21370*
9.26410
Porcelain
9.12456*
9.14236
9.24193*
9.19193*
9.11246*
9.14615
9.28257
9.28386*
9.26411*
Solid
9.25256
9.19256*
9.28245*
9.25256
9.19256*
Traditional - 9.01247*
Country - 9.01375*
Low Spout - 9.01737*
9.11245
9.07245
Service Kit
9.03245
9.
9.18256*
9.30257
9.14372*
9.20375*
9.25256
9.06745
9.17375*
COUNTRY
TRADITIONAL
LOW SPOUT
9.28448
9.27381*
9.27246*
Perrin & Rowe is a trademark of Avilion Ltd.
903245U/2
02/08
Fig 2.
Spare Parts - *Where indicated specify color
NOTE:
To utilize the rough installation cap it is necessary to remove the top
seating cage, please follow the first 5 points of the Diverter
Replacement section.
S P A R E P A R T S A N D S E R V I C E
3 Parker
Irvine
CA 92618
(714) 557-1933
O P E R A T I O N
Ceramic disc valves are fitted as standard to this mixer faucet. Flow from
FULLY OFF to FULLY ON is achieved by rotating the handles a quarter turn.
Diverting action is achieved by pulling up on the diverter knob. Higher water
pressures may make the diverting action difficult.
C A R E & M A I N T E N A N C E
Occasional cleaning with warm soapy water, followed by a polish with a soft
cloth is all that is required to keep the plated finish in good condition.
Do not use proprietary abrasive liquids, powders, or pads to clean the
faucet. You will damage the plated finish and void your warranty.
The aerator at the outlet of the spout may need occasional cleaning. This is
accomplished by unscrewing the outlet in an counter-clockwise
direction, dismantling and leaving the inner screen mesh immersed
overnight in vinegar or lemon juice.
DO NOT use chemical descaling
liquids for this purpose.
Rinse thoroughly in clean water and re install.
D I V E R T O R R E P L A C E M E N T
Unscrew the divertor knob from the spindle by lifting the knob and
gripping the flats on the spindle with a 5mm spanner, then unscrew.
Undo the screw in the back of the nozzle using the hexagon key
provided.
Lift the nozzle off base ring and shank.
Unscrew top seating cage and remove.
Replace diverter plate sub-assembly’.
Reassemble the nozzle, check fitting carefully for leaks.
Reassemble the divertor knob.
H A N D L E V A R I A N T S
Both porcelain and solid levers are included with U.3248L U. 3737L and U.3745L models.
H O W T O C H A N G E
D
E
F
A
C
B
A
B
E
1
1)) Unscrew lever bolt A
A from lever ball B
B by
hand.
2
2)) Remove metal lever insert C
C and seal D
D.
3
3)) Place one of the replacement seals E
E onto
lever bolt A
A and slide to the end. Place
porcelain lever insert FF onto lever bolt A
A
and slide to the end of the bolt.
4
4)) place the other replacement seal E
E onto
lever bolt A
A and slide to the end of the
porcelain lever insert.
5
5)) Screw lever bolt and porcelain lever insert
assembly back into lever ball B
B and screw
down tightly by hand
9.28385*
