manualshive.com logo in svg

Rohde & Schwarz TS-PSAM, Руководство пользователя

Поделиться
Скачать
Rohde & Schwarz TS-PSAM Скачать руководство пользователя страница 15

Layout

R&S

®

TS-PSAM

13

User Manual 1142.9878.12 ─ 12

4

 

Layout

4.1

 

Mechanical Construction of the R&S TS-PSAM

On this topic, see also 

Figure 4-1

.

The R&S TS-PSAM module is designed as a long cPCI plug-in module for mounting in
the front of the R&S CompactTSVP. The board height of the module is 3 HU (134 mm).
To ensure that it is inserted correctly into the Compact TSVP, the front panel is fur-
nished with a locating pin. The module is secured in place with the two retaining
screws on the front panel. Front connector X10 is used for connecting the UUTs. Con-
nector X30 connects the R&S TS-PSAM module to the analog bus backplane in the
R&S CompactTSVP. Connectors X20/X1 connect the R&S TS-PSAM module to the
cPCI backplane/PXI control backplane.

Figure 4-1: Arrangement of connectors and LEDs on the R&S TS-PSAM module

Table 4-1: Connectors on the R&S TS-PSAM module

Symbol

Use

X1

cPCI Bus

X10

UUT

X20

Extension (PXI), Rear I/O

X30

Analog Bus

Mechanical Construction of the R&S TS-PSAM

Содержание TS-PSAM



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды