R&S FSU
Firmware Release 4.61 SP3
12
E-33
29. (V4.11) GPIB: Basic remote control of the signal generator which is connected to the additional
FSP-B10 GPIB Interface.
30. (V4.11) GPIB: SCPI format for binary block data extended for byte counts > 999.999.999 bytes.
31. (V4.11) GPIB: New commands available
:[SENSe<1|2>:]CORRection:TRANsducer:ACTive?
returns active transducer
:CALCulate<1|2>:LIMit<1...8>:ACTive?
returns active limit line(s)
32. (V4.11) Trigger Line for video trigger is now also visible outside of the trigger menu.
33. (V4.11) Extended resolution for the number of sweep points.
In addition to currently allowed values an increment of 100 is possible now for number of points
_
201.
34. (V4.11) HP emulation: The OL command returns the mixer level in byte 23
35. (V4.11) HP emulation:
The commands MKPK NH | NL | NR and KSK do not perform a sweep start
when marker is already switched on
36. (V4.11) HP emulation:
The commands SNGLS and CONTS are setting the command complete bit
(bit 4) in STB
37. (V4.11) HP emulation: New s
oftkey SETUP - GENERAL SETUP - GPIB - SWEEP REP ON/OFF"
38. (V4.11) HP emulation:
New commands: VARDEF, CTA, ADD, SUB, MPY, DIV
39. (V4.11) HP emulation:
New command NORMLIZE for tracking generator
40. (V4.11) HP emulation:
The command LF performs a reset
41. (V4.11) LXI Class C support
42. (V4.11) Measurement speed improved for EMI filter available (spectrum mode / frequency
domain).
43. (V4.11 SP1) New model R&S FSU67 supported.
44. (V4.11SP1) New CPU Board 1091.3104 supported (with the exception of option B73).
45. (V4.11SP2) Option B73 now supported with new CPU Board 1091.3104, too.
46. (V4.21) New Save/Recall menu and dialogs available.
47. (V4.21) An easy access to the Windows XP Start menu is available.
48. (V4.21) The required sweeptime is reduced for video bandwidth < resolution bandwidth.
49. (V4.21) ASCII Export available for Marker Peak List.
50. (V4.21) Adjustable marker position knob stepsize is available.
51. (V4.21) New trace average function Power added.
52. (V4.21) HP emulation: Personality Spurious supported.
53. (V4.21) HP emulation: Personality Phase Noise supported.
54. (V4.21) New Service function
0.6.0 to check installation of option FSU-K51
The function returns 0 / 1 if FSU-K51 is not installed / installed.
Example: "DIAG:SERV:SFUN? '0.6.0' "
55. (V4.21) FSP-B10: Upper frequency limit of SMF100A is now 43.5 GHz .
56. (V4.21) The Aquisition Time (for FFT filter) is now readable with remote command
"SENS:SWE:TIME?".
57. (V4.21 SP1) FSP-B10: Support for SMA100, SMB100 (1/2/3/6GHz), SMF (22/43GHz) SMJ (3/6GHz).
58. (V4.21 SP1) FSP-B10: Support for SMF100a - TTL mode.
59. (V4.21 SP1) FSU-B21 with Order Number 1157.1126.03
supported
.
