manualshive.com logo in svg

Rohde & Schwarz CMW-KM645, Руководство пользователя

Поделиться
Скачать
Rohde & Schwarz CMW-KM645 Скачать руководство пользователя страница 48

Command Reference

R&S

®

CMW-KM645

48

User Manual 1173.9740.02 ─ 04

6.5 Limits

The following commands define limits for the "FM Stereo Radio" measurement results.

CONFigure:FMSTereo:MEAS<i>:MEValuation:LIMit:RFCarrier

.............................................48

CONFigure:FMSTereo:MEAS<i>:MEValuation:LIMit:RFModulation

.......................................49

CONFigure:FMSTereo:MEAS<i>:MEValuation:LIMit:AFLeft

................................................. 50

CONFigure:FMSTereo:MEAS<i>:MEValuation:LIMit:AFRight

............................................... 50

CONFigure:FMSTereo:MEAS<i>:MEValuation:LIMit:RFCarrier 

<CarrierPowLower>,

<CarrierPowUpper>, <CarrFreqErrUpp>, <MDevPeakUpper>,
<MDevRmsUpper>, <CarrierPowEnab>, <CarrFreqErrEnab>,
<MDevPeakEnable>, <MDevRmsEnable>

Defines upper limits for the measurement results which characterize the RF carrier
properties and disables/enables the limit check.

Parameters:

<CarrierPowLower> Lower limit for RF carrier power

Range: 

-80 dBm  to  0 dBm

*RST: 

-35 dBm

<CarrierPowUpper> Upper limit for RF carrier power

Range: 

-80 dBm  to  0 dBm

*RST: 

-25 dBm

<CarrFreqErrUpp>

Upper limit for RF carrier frequency
Range: 

0 Hz  to  1500 Hz

*RST: 

960 Hz

<MDevPeakUpper>

Upper limit for peak multiplex deviation
Range: 

0 Hz  to  96E+3 Hz

*RST: 

76E+3 Hz

Default unit: Hz

<MDevRmsUpper>

Upper limit for RMS multiplex deviation
Range: 

0 Hz  to  96E+3 Hz

*RST: 

192 Hz

Default unit: Hz

<CarrierPowEnab>

OFF | ON
Disable/enable limit check for RF carrier power
*RST: 

OFF

<CarrFreqErrEnab> OFF | ON

Disable/enable limit check for RF carrier frequency error
*RST: 

OFF

<MDevPeakEnable> OFF | ON

Disable/enable limit check for peak multiplex deviation
*RST: 

OFF

 

Limits

深圳德标仪器 

135-1095-0799

Содержание CMW-KM645


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды