Rohde & Schwarz 1138.4000 Скачать руководство пользователя | Manualshive

Страница: 111 / 213

background image

Radio Unit R&S

CRTU-RU

Module Replacement

1140.0050.82 3.37

E-4

After the adjustment has been terminated, the operating software starts automatically and the CRTU
Radio Unit is ready for use and complies with the specifications, except for the high-precision level
accuracy.

In order to achieve the level accuracy as described in the data sheet, a so-called path error data record
is necessary.

To this end, the CRTU Radio Unit must be measured using the test system ACS 100 (see chapter 1,

Performance Test

).

Replacing the DIGITAL BOARD

(see chapter 5,

spare part list, Current No. 390

and

explosion drawing 1138.4000.01 D sheet 2

)

The DIGITAL BOARD is incorporated in the module support as plug-in module. For replacement
proceed as follows:

Opening the instrument and removing the DIGITAL BOARD

¾

Switch off the instrument, pull the mains plug and unscrew the rear-panel feet.

¾

Place the instrument onto the front carrying handles, push the tube upwards and take off.

¾

After unscrewing the two countersunk screws at the top left instrument frame, slightly lift the cover at

the instrument top, slightly push to the right and lift off.

¾

Pull off all the MMCX plug-in cables (using a pull-out tool

∗

) from the top of the DIGITAL BOARD and

pull off the module towards the top using the two levers on the right and left.

Installing the new DIGITAL BOARD and completing the instrument

¾

Insert the new DIGITAL BOARD into the instrument in the reverse order and connect all the MMCX

plug-in cables.

¾

Complete the instrument without causing damage to the cables.

¾

Connect the instrument to the mains.

¾

Connect the external keyboard to an USB connector of the CRTU Radio Unit.

¾

Switch on the CRTU Radio Unit.

Automatic module data adjustment

¾

Boot up within BootMagic



menu into “DOS OPSW / Service” or “Service / WCDMA”.

¾

During startup observe the display.

¾

When three BEEPs can be heard, press the MENU SELECT key.

¾

The version manager is started (see also chapter 4, Firmware update). The display includes the

menu item FIRMWARE UPDATE AFTER BOARD CHANGE.

¾

Press the softkey to the left of the above mentioned menu item.

The automatic module data adjustment is performed under software control, firmware updates for
microprocessors and programmable devices being performed as well. This may take a few minutes.

∗

available in CMU-Service Kit CRTU-Z3 (1139.0509.02)

«
...
109
110
111
112
113
...
»

Содержание 1138.4000






















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1138.4000

Бренд: Baker Hughes Страницы: 168

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

Бренд: Xebex Fitness Страницы: 15

Бренд: qeedo Страницы: 2

Бренд: Zell Страницы: 32

Бренд: Uflex Страницы: 16

Air 2000 Outdoor

Бренд: ubbink Страницы: 21

Бренд: Nakayama Страницы: 14

Бренд: Qlight Страницы: 4

mocon AQUATRAN 3/38

Бренд: Ametek Страницы: 85

CB Ohio Special 100 HP

Бренд: CleaverBrooks Страницы: 200

Бренд: AS MOTOR Страницы: 36

Бренд: HOMCOM Страницы: 11

Powerator 1800 compact

Бренд: Seto Страницы: 39

Бренд: Veeder-Root Страницы: 58

Бренд: G-FITNESS Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды