Rohde & Schwarz 1138.4000 Скачать руководство пользователя

Страница: 68 / 213

Manual Adjustment

Radio Unit R&S

CRTU-RU

1140.0050.82 2.2

E-3

Preparing the Instrument

Opening the casing:

Remove the power plug on the CRTU Radio Unit and place the

instrument onto the front handles.

Loosen the four size 20 Torx screws at the four rear-panel feet

and take off the feet.

Pull off the instrument tube towards the top.

Locate the adjustment devices (see chapter 5, drawing

1100.0008.01 D, page 3. The location of the adjustment points is
analogous to the CMU).

After performing the manual adjustment, close the casing again

in the reverse order.

Note:

If only the Option OCXO REFERENCE OSC. CRTU-B2 is to be
adjusted, it is not necessary to open the complete tube of the CRTU
Radio Unit. The adjustment can be made from outside through the
ventilation holes using a small screwdriver.

Adjusting the + 5 VDC Reference Voltage

Preparation:

Connect the DC voltmeter test cable to the SMB plug X221 on

the motherboard.

Switch on the

CRTU Radio Unit

and allow it to warm up for

approx. 5 minutes.

Adjustment:

Use potentiometer R120 on the REFERENCE BOARD to adjust

the measured value at the DC voltmeter to + 5.000 V ± 1 mV.

Adjusting the 10 MHz Reference Frequency

Preparation:

The measurement can be performed either at connector REF OUT1
(rear of

CRTU Radio Unit

) at 10 MHz or at connector RF3 OUT

(front) at 1 GHz using a frequency counter.

For the measurement at connector RF3 OUT set the generator to

1 GHz and 13 dBm without modulation in the RF menu.

For the adjustment, the

CRTU Radio Unit

must be set to internal

reference source.

This setting is to be selected in the

Connection Control – Sync.

menu.

Note:

The measurement at 1 GHz can be performed with a lower frequency
counter resolution (1 Hz) in order to achieve a faster adjustment.

Содержание 1138.4000






















































































































































































































Результаты поиска

Содержание 1138.4000

Отзывы:

Похожие инструкции для 1138.4000

Бренды по названию

Популярные бренды

Rohde & Schwarz 1138.4000, Руководство по обслуживанию

Результаты поиска

Содержание 1138.4000

Отзывы:

Похожие инструкции для 1138.4000

Бренды по названию

Популярные бренды