You have purchased one of the finest car-audio trunk box
subwoofers available today. RODEK ported subwoofers are
engineered and manufactured to set new benchmarks of bass
performance and technical reliability.
Both RN-BR models deploy ported cabinets with large cross
section slot ports for port noise free operation and high SPL.
Both box models use cabinets made of MDF with internal
cross bracing and are equipped with RW10 or RW12 woofers.
Please read and follow the provided installation and operating
instructions carefully, in order to benefit from the full sound
quality and performance potential of this high quality
product.
Special Features
■
Loaded with a RODEK RW10 or RW12 subwoofer
■
Slot ports with large cross section for port noise free
operation
■
CNC routed MDF enclosure with inner bracing
■
Enclosure with carpet cover and PA-painted front
■
Space optimized angled rear wall construction
■
Spring-loaded terminal
Placement
➞
Connection
➞
Settings
Basically, your trunkbox subwoofer is designed to be placed
in the trunk compartment of your car. The terminal binding
posts allow quick and easy installation or removal of the trunk
box – if necessary.
Only start doing adjustments of the amps or headunits
lowpass filter or the input gain, after setting „treble“, „bass“
and „loudness“ controls on the head unit to neutral/zero
position.
Your bandpass subwoofer needs a low-pass filtered signal
with 12dB/oct. slope for best sound quality.
➞
Connect the speaker wire of your subwoofer amp channel
terminal of the subwoofer system.
➞
Set the lowpass crossover frequency of the channel(s)
driving the sub to approx. 80 Hz.
➞
Increase the input gain of the subwoofer channel, until bass
output is full sounding and loud enough.
➞
Turn down the volume and try both electrical in-phase and
out-of-phase polarity connections to find the one giving
you more bass quantity and quality.
„In-phase“ connection of your subwoofer is critical – if your
sub plays out of phase, the output at the crossover frequency
region will be depressed due to cancellation effects.
Thus one connection polarity will give you a „fuller“ and more
dynamic bass reproduction in the 80Hz range.
PORTED TRUNK BOX SUBWOOFER
Specifications
RN110BR
RN112BR
Peak Input Power:
350 W
400 W
Continuous Input Power:
200 W RMS
250 W RMS
Frequency Response (In-Car -3dB):
30 – 150 Hz
25 – 150 Hz
Sensitivity (1W/1m):
91 dB
93 dB
Nominal Impedance:
4 ohms
4 ohms
Dimensions (WxHxD):
450 x 340 x 250/355 mm
535 x 380 x 270/385 mm
RN110BR/RN112BR
12300 Edison Way · Garden Grove · CA 92841 U. S. A.
www.rodek.com
Limited warranty 2 years, starting from purchase at retail.
This warranty does not cover any damage due to:
1. Speaker overload due to excessive or distorted amplifier power etc.
2. Exposure to excessive humidity, fluids, heat, direct sunrays or excessive dirt
or dust.
3. Accidents or abuse, unauthorized repair attempts and modifications not
explicitly authorized by the manufacturer
WARRANTy CoNDITIoNS
This warranty is limited to the repair or the replace-
ment of the defective product at the manufacturer´s
option and does not include any other form of da-
mage, whether incidential, consequential or other-
wise.
This warranty will not cover any loss during trans-
portation, transport costs or any other damage
caused by transport or shipment of the product.
For safety and legal reasons, it might be prohibited using the box illumination while operating a car. Restrictions may apply
in certain countries. For making sure to follow all national requirements and not to distract drivers attention, we recommend
connecting the box illumination to the interior light of the trunk.
