Rockwell ShopSeries RS5105, Руководство пользователя, Страница: 11 / 16

11
96W Multi ShaRpeneR en
5) Turn the drill bit until the V guide fully drops
over it. All four drill bit corners should now be
touching the V guide sides. (See Fig.E)
6) Ensure that the drill and holder are fully down in
the setting slot. With the drill bit in this position,
tighten the clamping ring in clockwise direction.
(See Fig. E)
7) Lift up the “V” guide and remove the clamp and
drill bit. (See Fig. F)
8) Transfer the clamp and drill bit into the clamp
holder. (See Fig. G)
9) Switch the power unit on. (See Fig. A)
10) Move the clamp holder from side to side as
indicated by the arrow on the sharpener,
securing with light finger pressure. (See Fig. H)
11) Remove drill bit and clamp and turn over (See
Fig. I). Repeat Step (10).
12) Check the leading edge of both flutes are equally
sharp. They should meet exactly in the middle as
in J1, not J2.
13) Switch the power unit off. Before removing the
module, ensure the grinding wheel has stopped.
3. ShaRpeninG KniVeS
WaRninG: Before assembling the knife &
scissor sharpener (8), be sure the tool is
unplugged and the on/off switch (11) is in ‘’O’’
position.
nOte: This module is suitable for all straight edged,
household knives and scissors only.
Do not use serrated edged blades.
1) Slide module labeled Knife & Scissor Sharpener
(8) on to the power unit.
2) Switch the power unit on.
3) Hold the knife handle towards you and insert the
handle end of the blade into knife sharpening
slot (10). (See Fig. K)
4) As soon as the blade touches the grinding wheel,
draw it with light steady pressure across the
wheel to the tip, then remove. Do not press hard.
5) Insert the second side of the blade into the other
top guide slot and repeat step (4). (See Fig. L)
6) Repeat sharpening each side in turn until a clean
sharp edge is attained.
7) Switch the power unit off. Before removing the
module, ensure that the grinding wheel has
stopped.
4. ShaRpeninG SCiSSORS
WaRninG: Before assembling the knife &
scissor sharpener (8), be sure the tool is
unplugged and the on/off switch (11) is in “O’’
position.
nOte: This module is suitable for all straight edged,
household knives and scissors only.
Do not use serrated edged blades.
1) Slide module labeled Knife & Scissor Sharpener
(8) onto the power unit.
2) Switch the power unit on.
3) Open the scissors fully.
4) Slide the first scissor blade through the scissor
sharpening slot. Keep the pivot of the scissors
and other blade to right hand side. (See Fig. M)
5) Draw the blade across the grinding wheel from
pivot to tip. Use a light steady pressure, do not
press too hard.
6) Remove and turn scissors over to sharpen the
second blade. Keep the pivot to the right and
sharpen from pivot to tip. (See Fig. N)
7) Repeat if necessary, until clean sharp edges are
achieved.
8) Switch the power unit off. Before removing the
module, ensure that the grinding wheel has
stopped.
5. ShaRpeninG ChiSel & plane bladeS
WaRninG : Before assembling the chisel
& plane sharpener (12), be sure the tool is
unplugged and the on/off switch (11) is in “O’’
position.
1) Slide the module labeled Chisel & Plane
Sharpener (12) onto the power unit.
2) Place the blade against the back lip of the plate.
The magnet (13) helps to hold it in place. (See
Fig. O)
3) The sharpening angle must match the existing
beveled angle on the blade tip. Adjust, if
necessary.
4) To alter the angle:
1. Loosen the angle adjusting knob (15) in anti-
clockwise direction.
2. Adjust the plate. The sharpening angle is
indicated by the small arrow. The adjustable
grinding angle is from 15° to 50°.Make sure the
blade edge touches the grinding wheel.
3. Tighten the angle adjusting knob. (See Fig. P)
5) Switch the power unit on.
6) Slide the blade and plate with light steady
pressure back and forth across the grinding