Rockwell RS2314 ShopSeries, Руководство пользователя, Страница: 11 / 12

11
18V CORDLESS DRILL EN
bit at the point to be drilled. Depress the switch trigger
to start the tool. Move the drill bit into the workpiece,
applying only enough pressure to keep the bit cutting.
Do not force or apply side pressure to elongate a hole.
When drilling in metal, only use HSS drill bits
in good condition. When screw-driving, apply a
small quantity of liquid soap or similar to the screw
threads to ease insertion.
8. DISPOSAL OF AN EXHAUSTED BATTERY PACK
To preserve natural resources, please recycle
or dispose of the battery pack properly. This
battery pack contains lithium batteries. Consult
your local waste authority for information regarding
available recycling and/or disposal options. Discharge
your battery pack by operating your drill, then remove
the battery pack from the drill housing and cover the
battery pack connections with heavy duty adhesive
tape to prevent short circuit and energy discharge. Do
not attempt to open or remove any of the components.
9. OVERLOAD PROTECTION
When overloaded, the motor comes to a stop.
Release the on/off button, and the machine will restart
immediately.
10. TEMPERATURE DEPENDENT OVERLOAD PROTECTION
When using as intended for the power tool cannot be
subject to overload. When the load is too high or the
allowable battery temperature of 75°C is exceeded,
the electronic control switches off the power tool until
the temperature is in the optimum temperature range
again.
11. PROTECTION AGAINST DEEP DISCHARGING
The Li-Ion battery is protected against deep
discharging by the “Discharging Protection System”.
When the battery is empty, the machine is switched off
by means of a protective circuit: The inserted tool no
longer rotates.
TROUBLESHOOTING
1. WHY DOES THE DRILL NOT TURN ON WHEN YOU PRESS
THE SWITCH?
The forward/reverse rotation control, which is on top
of the trigger, is positioned in the lock function. Unlock
the forward/reverse rotation control by putting it into
the required rotation position. Push the trigger and the
drill will start to rotate.
2. THE DRILL STOPS BEFORE THE SCREW IS COMPLETELY
TIGHTENED. WHY?
Verify the torque position of the variable clutch, you
can find the variable clutch between the chuck and
the drill body. Position 1 is the lowest torque (screw
driving force) and position 16 is the highest torque
(screw driving force). Position 17 is for drill operation.
Regulate the variable clutch to a higher position to
reach the best result.
3. I CANNOT FIT THE BATTERY INTO THE BATTERY
CHARGER. WHY?
The battery can be inserted into the charger only in
one direction. Turn the battery around until it can be
inserted into the slot.
4. REASONS FOR DIFFERENT BATTERY PACK WORKING
TIMES
Charging time issues, as above, and having
not used a battery pack for a prolonged time
will reduce the working life of the battery pack.
This can be corrected after several charge and
discharge operations by charging & working with
your drill. Heavy working conditions such as large
screws into hard wood will use up the battery pack
energy faster than lighter working conditions.
Do not re-charge your battery pack below 0
o
C
and above 45
o
C as this will affect performance.
MAINTENANCE
Your tool requires no additional lubrication or
maintenance.
There are no user serviceable parts in your tool,
battery pack or charger. Never use water or chemical
cleaners to clean your tool. Wipe clean with a dry
cloth. Always store your tool in a dry place. Keep the
motor ventilation slots clean. Occasionally you may
see sparks through the ventilation slots. This is normal
and will not damage your power tool.
Staple your purchase receipt here
Before returning this product for
warranty or any other reason, please call.
POSITEC AUSTRALIA PTY LIMITED
ABN 14 101 682 357
Unit 15, 23 Narabang Way Belrose 2085
NSW Australia
FREE CALL 1300 889 028
EMAIL:office.sales@positec.com.au