Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 548

background image

36

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

Chapter 2

Get Started

4. Connect a Category 5 Ethernet cable from the flashing switch port to

the Ethernet port on a computer.

or

For 1783-BMS4S2SGL or 1783-BMS4S2SGA switches, do one of the
following:
• Insert a copper SFP module into the Gi1/1 port on the switch. Then

connect a Category 5 Ethernet cable from the SFP module to the
Ethernet port on the computer.

• Connect the Gi1/1 port on the switch to the Ethernet port on the

computer by using a fiber-to-Ethernet media converter.

Once you connect the switch to the computer, the following occurs:
• The status indicator for the port connected to the computer changes

from flashing green to solid green.

• The switch acts as a DHCP server on VLAN 1000 with an address of

169.254.0.1.

• The switch assigns the computer an IP address of 169.254.0.2 on

VLAN 1000.

• The Setup status indicator changes from flashing green to solid

green.

5. Proceed to

Configure Network Settings via Device Manager on page 39

.

Run Multi-mode Express Setup in Medium Press Mode

Be aware of the following conditions that cause the switch to exit Medium
Press mode.

IMPORTANT

Port Gi1/1 does not flash during setup, but must be used to connect
1783-BMS4S2SGL or 1783-BMS4S2SGA switches to a computer.

IMPORTANT

The IP address of the switch for multi-mode Express Setup is

different than the IP address for single-mode Express Setup.

Condition

Status Indicator Behavior

A non-default configuration exists on the switch.

The Setup status indicator turns red for 10 seconds.

No DHCP response is received for 10 minutes from when
the switch broadcast the request.

IMPORTANT

Before you begin, make sure that your system has a DHCP server configured
to assign the switch an IP address. You can configure a switch to be a DHCP
server, as described on

.

«
...
34
35
36
37
38
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

EasySmart DGS-1100-08

Бренд: D-Link Страницы: 44

Бренд: pathway Страницы: 28

Бренд: GE Страницы: 302

Бренд: Talkswitch Страницы: 17

IPS7110-2GC-8POE

Бренд: 3One data Страницы: 3

Бренд: Ultra Страницы: 20

Бренд: Lindy Страницы: 70

Бренд: SIIG Страницы: 17

FOS-3124 SERIES

Бренд: CTS Страницы: 223

Бренд: Davey Страницы: 2

USB 2.0 7-Port Hub HO97916

Бренд: GE Страницы: 19

Бренд: IOGear Страницы: 10

SL-5-DS-2 SWITCH AND CHECK VALVE

Бренд: BENDIX Страницы: 4

Champion SeriesKD-2x1CSK

Бренд: Key Digital Страницы: 6

SRW224P - 10/100 - Gigabit Switch

Бренд: Linksys Страницы: 69

ePowerSwitch 1GR2

Бренд: Neol Страницы: 47

SFP Field TAP Series

Бренд: Garland Страницы: 9

Бренд: Samson Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды