Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 238 | Manualshive

Страница: 238 / 548

background image

238

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

Chapter 7

Configure Switch Features

Dynamic Host Configuration
Protocol (DHCP) Persistence

Every device in an IP-based network must have a unique IP address. DHCP
assigns IP address information from a pool of available addresses to newly
connected devices (DHCP clients) in the network. If a device leaves and then
rejoins the network, the device receives the next available IP address, which is
not necessarily the same address that it had before.

The switch can be set to operate as a DHCP server to provide DHCP
persistence. With DHCP persistence, you can assign a specific IP address to
each port to make sure that a device that is attached to a specific port receives
the same IP address. This feature works with only one device that is connected
to each port configured for DHCP persistence. The DHCP server also serves
addresses to BOOTP clients.

Configure DHCP via Device Manager

To use DHCP persistence, complete this process:

1. Enable DHCP.

2. Configure the IP address pool.

3. Assign a specific IP address to each port.

Configure the DHCP Server

To enable the DHCP Server mode on the switch, do the following.

1. From the Configure menu, choose DHCP.

2. Check the Enable DHCP checkbox.

IMPORTANT

To make sure DHCP persistence works correctly, follow the application rules.

«
...
236
237
238
239
240
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

TNS5500D Series

Бренд: 3onedata Страницы: 5

IPS7112G-4GS-8GPOE

Бренд: 3onedata Страницы: 3

Бренд: netvox Страницы: 14

Tek-CARE NC554/8

Бренд: TekTone Страницы: 2

Бренд: Sven Страницы: 4

LMX-2602G-SFP Series

Бренд: ANTAIRA Страницы: 19

IPES-3424DSFP-2P

Бренд: Lantech Страницы: 26

Бренд: Black Box Страницы: 57

Бренд: Conrad Страницы: 8

Бренд: Lindy Страницы: 6

Бренд: Dusun Страницы: 18

Бренд: Enable-IT Страницы: 49

Бренд: Kramer Страницы: 33

Бренд: IN-COMMAND Страницы: 8

Бренд: Myson Страницы: 2

Бренд: ATEN Страницы: 31

Бренд: LevelOne Страницы: 17

Бренд: Mastervolt Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды