Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 548

background image

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

21

About the Switches

Chapter 1

Software Features

Switch software features can be configured via Device Manager, the
Logix Designer application, or both:

• See

Configuration via Device Manager on page 47

• See

Configuration via the Studio 5000 Environment on page 53

All features can be configured via the command-line interface (CLI).

Some features are available only on select switches and expansion modules.

Table 2 - Software Features

Feature

Switches

Device Manager

Logix Designer

Access Control Lists (ACLs)

All

•

—

Alarms

All

•

—

CIP Sync Time Synchronization/
Precision Time Protocol (PTP)

All Stratix 5400 switches
All Stratix 5410 switches
Stratix 5700 switches: 1783-BMS10CGN, 1783-BMS10CGP, 1783-BMS12T4E2CGNK,
1783-BMS12T4E2CGP, 1783-BMS20CGN, 1783-BMS20CGP, 1783-BMS20CGPK
ArmorStratix 5700 switches: 1783-ZMS4T4E2TGP, 1783-ZMS8T8E2TGP, 1783-ZMS4T4E2TGN,
1783-ZMS8T8E2TGN
All Stratix 8000/8300 switch base units (PTP traffic can be only forwarded through
expansion modules)

•

•

Device-level Ring (DLR)

All Stratix 5400 switches
Stratix 5700 switches: 1783-BMS10CGP, 1783-BMS10CGN, 1783-BMS12T4E2CGL,
1783-BMS12T4E2CGP, 1783-BMS12T4E2CGNK,1783-BMS20CL, 1783-BMS20CA,
1783-BMS20CGL, 1783-BMS20CGP, 1783-BMS20CGN, 1783-BMS20CGPK
ArmorStratix 5700 switches: 1783-ZMS4E4T2GP, 1783-ZMS8E8T2GP, 1783-ZMS8E8T2GN,
1783-ZMS8E8T2GN

•

•

Dynamic Host Configuration Protocol
(DHCP) Persistence

All

•

•

DHCP for Ring Devices

Stratix 5700 and ArmorStratix 5700 switches

•

Enhanced Interior Gateway Routing
Protocol (EIGRP)

Stratix 5400 switches with Layer 3 firmware
Stratix 5410 switches with Layer 3 firmware
Stratix 8300 base units

•

—

EtherChannels

All

•

—

Motion Prioritized QoS macros

Stratix 5400 switches
Stratix 5410 switches
Stratix 5700 switches with Full firmware
ArmorStratix 5700 switches

•

—

Horizontal stacking

Stratix 5410 switches: 1783-IMS28NAC, 1783-IMS28RAC, 1783-IMS28NDC, 1783-IMS28RDC

—

—

Internet Group Management Protocol
(IGMP) Snooping with Querier

All

•

—

Multi-mode Express Setup

Stratix 5400, 5410, 5700, ArmorStratix 5700, and Stratix 8000 switches

•

•

Network Address Translation (NAT)

All Stratix 5400 switches
All Stratix 5410 switches
Stratix 5700 switches: 1783-BMS10CGN, 1783-BMS20CGN, 1783-BMS12T4E2CGNK
ArmorStratix 5700 switches: 1783-ZMS4T4E2TGN, 1783-ZMS8T8E2TGN

•

•

Network Time Protocol

Stratix 5400 switches
Stratix 5410 switches
Stratix 5700 switches
ArmorStratix 5700 switches
Stratix 8000/8300 switches

•

—

«
...
19
20
21
22
23
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

Бренд: FANATEC Страницы: 40

Бренд: Field Controls Страницы: 4

Бренд: CZHOON Страницы: 4

Бренд: BERNSTEIN Страницы: 3

Бренд: Zektor Страницы: 65

Raritan Dominion LX II

Бренд: LEGRAND Страницы: 7

Бренд: VADA Страницы: 4

CEFLA PIR DALIP

Бренд: DANLERS Страницы: 2

D-PFS3110-8ET1GT1GF-96

Бренд: Dahua Страницы: 17

Бренд: Elk Products Страницы: 2

Бренд: Kramer Страницы: 4

Бренд: Yacoub Automation GmbH Страницы: 45

Бренд: Quark-Elec Страницы: 10

FS728TP - ProSafe 24 Port 10/100 Smart Switch

Бренд: NETGEAR Страницы: 261

Бренд: Gigabyte Страницы: 2

Бренд: Zenith Страницы: 24

Бренд: B&G Страницы: 11

Бренд: Accton Technology Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды