manualshive.com logo in svg

Rockwell Automation Guardmaster 440R-ENETR, Руководство пользователя, Страница: 43 / 86

Поделиться
Скачать
Rockwell Automation Guardmaster 440R-ENETR Скачать руководство пользователя страница 43

Rockwell Automation Publication 440R-UM009C-EN-P - July 2019

43

AOP Controller Tags

Chapter 6

DG Fault Codes

ResetHeldOn1

BOOL

Reset Held On Fault - Indicates that the reset signal at terminal X4 was held ON (1) for longer than the maximum time of 3000 ms.
0 = No fault
1 = Fault

NonRecoverableFault

BOOL

Nonrecoverable Fault Status - Indicates whether the DG safety relay has detected unexpected internal operation.
0 = No fault
1 = Fault

Fault

BOOL

Fault Status - Indicates whether the DG safety relay has detected unexpected operation of a monitored safety device.
0 = No fault
1 = Fault

FaultCode

INT

Fault Code - When a nonrecoverable fault occurs, the DG safety relay generates a value to help indicate the potential cause of the 
fault. See 

Table 4

 for a list of DG fault codes.

Config

INT

Configuration ID - Each configuration of the DG safety relay has a unique ID. You can use this tag to determine if the configuration 
changed.

ValueRotarySwitch

SINT

Value of Rotary Switch - The DG safety relay provides a unique value of each position of the timer rotary switch.

GuardLink1

AB:GSR_DG_GL:I:0

GuardLink1 Input and Output

GuardLink2

AB:GSR_DG_GL:I:0

GuardLink2 Input and Output

Table 3 - DG Relay Tags (Tag name prefix: ENETRname:I.Relayx_GSR_DG.)

Name

Data Type

Definition

Table 4 - DG Relay Nonrecoverable Fault Codes

Fault Code 
Decimal (Hex)

Description

Recommended Action

01 (01)

Pulse test output A stuck at 24V or 0V

Check the wiring and voltage at terminal S11.

02 (02)

Pulse test output B stuck at 24V or 0V

Check the wiring and voltage at terminal S21.

03 (03)

Power Fault

Terminal A1 is over 27V or under 20V. Measure and adjust the voltage at terminal A1 to 20.4…26.4V under all 
electrical load conditions.

04 (04)

Internal VCC (3.3V) is out of range

06 (06)

Internal fault

Follow the general instructions for faults.

10 (0A)

Internal relay feedback error

The internal force-guided relay has a feedback error. Replace unit.

13 (0D)

Pulse test output cross fault

Check for a short circuit between ChA S11/S12 and ChB S21/S22.

16 (10)

Terminal fault S11

Terminal issue when configured as output like Test Pulse Output A. Check the wiring at terminal S11.

17 (11)

Terminal fault S21

Terminal issue when configured as output like Test Pulse Output B. Check the wiring at terminal S21.

19 (13)

Terminal fault S22

Terminal issue when configured as GuardLink.
Check wiring on terminal S22.

21 (15)

Terminal fault S42

Terminal issue when configured as GuardLink.
Check wiring on terminal S22.

23 (17)

Terminal fault X2

Terminal issue when configured as OSSD/SWS. Check the wiring at terminal X2.

64 (40)

GuardLink-CH[0] no termination

Check and install terminator at end of GuardLink[0] circuit.

65 (41)

GuardLink-CH[1] no termination

Check and install terminator at end of GuardLink[1] circuit.

66 (42)

GuardLink-CH[0] no communication

Check wiring - brown wire is connected to 24V, blue wire is connected to ground, white wire is connected to S12, and 
black wire is connected to S22.

67 (43)

GuardLink-CH[1] no communication

Check wiring - brown wire is connected to 24V, blue wire is connected to ground, white wire is connected to S32, and 
black wire is connected to S42.

Содержание Guardmaster 440R-ENETR























































































Отзывы:

Нет отзывов