Rockwell Automation Allen-Bradley PowerFlex 4 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 94

Rockwell Automation Allen-Bradley PowerFlex 4 Скачать руководство пользователя страница 52

3-16

Programming and Parameters

Advanced Program Group

(continued)

A069 [Internal Freq]

Related Parameter(s):

Provides the frequency command to the drive when P038

[Speed Reference]

is set to 1 “Internal

Freq”. When enabled, this parameter will change the frequency command in “real time” using the
integral keypad Up Arrow or Down Arrow when in program mode.

Important:

Once the desired command frequency is reached, the Enter key must be pressed to store

this value to EEPROM memory. If the ESC key is used before the Enter key, the frequency will return
to the original value following the normal accel/decel curve.

Values

Default

60.0 Hz

Min/Max:

0.0/240.0 Hz

Display:

0.1 Hz

A070 [Preset Freq 0]

(1)

A071 [Preset Freq 1]
A072 [Preset Freq 2]
A073 [Preset Freq 3]

Related Parameter(s):

Provides a fixed frequency command value when A051 - A052

[Digital Inx Sel]

is set to 4 “Preset

Frequencies”.

(1)

To activate A070 [Preset Freq 0] set P038

[Speed Reference]

to option 4 “Preset Freq 0-3”.

Values

A070 Default
A071 Default
A072 Default
A073 Default

0.0 Hz
5.0 Hz
10.0 Hz
20.0 Hz

Min/Max:

0.0/240.0 Hz

Display:

0.1 Hz

Input State of Digital In 1

(I/O Terminal 05)

Input State of Digital In 2

(I/O Terminal 06)

Frequency Source

Accel / Decel Parameter Used

(2)

0

0

A070 [Preset Freq 0]

[Accel Time 1] / [Decel Time 1]

1

0

A071 [Preset Freq 1]

[Accel Time 1] / [Decel Time 1]

0

1

A072 [Preset Freq 2]

[Accel Time 2] / [Decel Time 2]

1

1

A073 [Preset Freq 3]

[Accel Time 2] / [Decel Time 2]

(2)

When a Digital Input is set to “Accel 2 & Decel 2”, and the input is active, that input overrides the settings in
this table.

A078 [Jog Frequency]

Related Parameter(s):

Sets the output frequency when a jog command is issued.

Values

Default

10.0 Hz

Min/Max:

0.0/P035

Display:

0.1 Hz

userman.book Page 16 Friday, June 21, 2002 2:48 PM

«
...
50
51
52
53
54
...
»

Содержание Allen-Bradley PowerFlex 4































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды