Rockwell Automation Allen-Bradley PowerFlex 4 Скачать руководство пользователя страница 46

Страница: 46 / 94

3-10

Programming and Parameters

Basic Program Group

(continued)

P037 [Stop Mode]

Related Parameter(s):

Active stop mode for all stop sources [e.g. keypad, run forward (I/O Terminal 02), run reverse (I/O
Terminal 03), RS485 port] except as noted below.

Important:

I/O Terminal 01 is always a coast to stop input except when P036 [Start Source] is set for

“3-Wire” control. When in three wire control, I/O Terminal 01 is controlled by P037 [Stop Mode].

Options

“Ramp, Clear Fault”

(1)

(Default)

Ramp to Stop. “Stop” command clears active fault.

“Coast, Clear Fault”

(1)

Coast to Stop. “Stop” command clears active fault.

“DC Brake, Clear
Fault”

(1)

DC Injection Braking Stop. “Stop” command clears active
fault.

“DC Brake w/Shutoff,
Clear Fault”

(1)

DC Injection Braking Stop with Auto Shutoff.

•

Standard DC Injection Braking for value set in A080

[DC

Brake Time]

•

Drive shuts off if the drive detects that the motor is
stopped.

“Stop” command clears active fault.

“Ramp”

Ramp to Stop.

“Coast”

Coast to Stop.

“DC Brake”

DC Injection Braking Stop.

“DC Brake w/Shutoff”

DC Injection Braking Stop with Auto Shutoff.

•

Standard DC Injection Braking for value set in A080

[DC

Brake Time]

•

Drive shuts off if current limit is exceeded.

(1)

Stop input also clears active fault.

userman.book Page 10 Friday, June 21, 2002 2:48 PM

Содержание Allen-Bradley PowerFlex 4































































































Результаты поиска

Содержание Allen-Bradley PowerFlex 4

Отзывы:

Похожие инструкции для Allen-Bradley PowerFlex 4

Бренды по названию

Популярные бренды

Rockwell Automation Allen-Bradley PowerFlex 4, Руководство пользователя

Результаты поиска

Содержание Allen-Bradley PowerFlex 4

Отзывы:

Похожие инструкции для Allen-Bradley PowerFlex 4

Бренды по названию

Популярные бренды