manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 4, Руководство пользователя

Поделиться
Скачать
Rockwell Automation Allen-Bradley PowerFlex 4 Скачать руководство пользователя страница 28

1-18

Installation/Wiring

Accel/Decel Selection 

The selection of Accel/Decel rates can be made through digital inputs, 
RS485 (DSI) communications and/or parameters.

 Jog Input

Enabled and Active:

A051 or A052 = 2

Yes

A079 [Jog Accel/Decel] used.

No

P039 [Accel Time 1]/P040 [Decel Time 1]

are used.

 RS485 (DSI) Port

Controls Speed

Yes

Active when

A067 [Accel Time 2]/A068 [Decel Time 2]

is selected by RS485 (DSI) port.

No

 Input is programmed

as “Accel 2 & Decel 2”

A051 or A052 = 1

Yes

A067 [Accel Time 2]/A068 [Decel Time 2]

is active when input is active.

No

 Speed is controlled

by [Preset Freq x]
A051 or A052 = 4

Yes

P039 [Accel Time 1]/P040 [Decel Time 1]; 

A067 [Accel Time 2]/A068 [Decel Time 2]

determined by the active

Preset Frequency.

See A070-A073 [Preset Freq 0-3]

on 

page 3-16

.

No

userman.book  Page 18  Friday, June 21, 2002  2:48 PM

Содержание Allen-Bradley PowerFlex 4































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды