manualshive.com logo in svg

Rockwell Automation Allen-Bradley Kinetix MMA-B080 Series, Руководство по установке

Поделиться
Скачать
Rockwell Automation Allen-Bradley Kinetix MMA-B080 Series Скачать руководство пользователя страница 53

Rockwell Automation Publication MM-IN001B-EN-P - February 2022

53

Kinetix MMA Asynchronous Main Motors Installation Instructions

b. Remove the sets of hardware that hold the blower assembly to the blower housing. See 

step 8

 for additional information. Keep the hardware; you use them to attach 

the cover in 

step 8

.

c. Lift and remove the blower assembly from the blower housing.

4.

If you have an axial blower, disconnect and remove the fan. 

See 

Table 54

 for 

screw types and torque values.
a. Remove the four nuts that secure the rear blower cover to the motor.
b. Remove the four screws on the blower terminal box and the remove cover.
c. Disconnect the wires in the blower terminal box. See 

Table 20 on page 27

 

for additional information.

d. Remove the screws that secure the fan to the blower housing.
e. Reattach the blower terminal box cover using the screws from 

step b

.

See 

Table 54

 for torque values.

f. Remove the four screws on the feedback connector.
g. Slide the blower housing out approximately 8 cm (3 in.).
h. Disconnect the ground wire from the spade connector located near the 

feedback connector inside of the blower housing.

i. Slide the feedback connector wires through the slit. Secure it to the motor.
j. Slide the blower housing an additional distance.
k. Remove the fan and fan nuts from the blower housing.

l. Reattach the fan nuts and screws to the blower housing.

See 

Table 54

 for torque values.

m. Slide the blower housing toward the motor. Stop at approximately 

8 cm (3 in.). 
- For shaft height 100 without the brake option, insert the bolts threads into the motor and blower housing.

n. Reattach the ground wire to the spade connector mentioned in 

step h

. 

o. Reattach the feedback connector by using the screws in 

step f

. 

See 

Table 54

 for torque values.

p. Slide the blower housing the remaining distance to the motor. For shaft height 100, reinsert and tighten the threaded bolts. See 

Table 57

 for torque values.

q. Reattach the four nuts to the rear blower cover that were removed in 

step a

. 

See 

Table 54

 for torque values.

5.

Remove the blower guard or blower cover from the rear side of the motor by removing the screws. See 

Table 55

 for quantity and type.

Figure 21 - Blower Housing Guard and Cover

ATTENTION: 

The blower assembly is not balanced when lifted. Take precautions to avoid swinging, 

personal injury, or equipment damage.

IMPORTANT

For shaft height 100 without the brake option, the blower 
housing is attached by using long bolts that get removed 
during this procedure. All other shaft heights use 
extension rods that attach to the motor.

Table 54 - Axial Blower Torque Values

Step

Motor Shaft Height

Screw/Nut Size

Torque

N•m (lb•in)

Step

Motor Shaft Height

Screw/Nut Size

Torque

N•m (lb•in)

(a and q) blower cover

SH80 

(1)

and SH100

(1)

There is no IC-17 clean-air option for shaft height 80. It is included in this table for direct axial to axial blower housing replacement procedures only.

M5

3 (26.55)

(d and l) fan screws

all

Phillips

Hand-tighten

SH132 and SH160

M8

9 (79.66)

(b and e) blower terminal box

Phillips

Hand-tighten

SH180

M10

25 (221.27)

(f and o) feedback connector

M3

1.1 (9.74)

SH225

M16

50 (442.54)

(a) (q)

 x4

(d)

 

( l )

(c)

 

(f) (o) 

x4

(g)

(h) (n)

(i)

( j )

(k)

(m)

(d)

 

( l )

(p)

(b) (e)

 x4

Figure 20 - Axial blower removal

Axial Blower

Radial Blower

Содержание Allen-Bradley Kinetix MMA-B080 Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды