background image

1

40752-195 (1)

 

Effective 

2

/201

1

Installation Instructions for Bul. 140

U

 N-Frame Circuit Breakers and Molded 

Case Switches

DO NOT ATTEMPT TO INSTALL OR PERFORM MAIN-

TENANCE ON EQUIPMENT WHILE IT IS ENERGIZED.  

DEATH, SEVERE PERSONAL INJURY, OR SUBSTAN-

TIAL PROPERTY DAMAGE CAN RESULT FROM 

CONTACT WITH ENERGIZED EQUIPMENT.  ALWAYS 

VERIFY THAT NO VOLTAGE IS PRESENT BEFORE 

PROCEEDING WITH THE TASK, AND ALWAYS FOL-

LOW GENERALLY ACCEPTED SAFETY PROCE-

DURES.

ALLEN-BRADLEY 

IS NOT LIABLE FOR THE MIS

APPLI-

 

CATION 

OR MISINSTALLATION OF ITS PRODUCTS.

The user is cautioned to observe all recommendations, 

warnings and cautions relating to the safety of personnel 

and equipment as well as general and local health and 

safety laws, codes and procedures.

The recommendations and information contained herein 

are based on Rockwell experience and judgement, but 

should not be considered to be all-inclusive or covering 

every application or circumstance which may arise.  If any 

questions arise, contact Rockwell for further information 

or instructions.

1.  INTRODUCTION

The N-Frame Circuit Breaker (Figure 1-1) are 690VAC 

maximum rated devices, 600V for UL applications, and 

have integral trip units.  Available current ratings are up 

to 1600 Amp, 1200 for UL applications.  I N-Frame Circuit 

Breakers and molded case switches are listed in ac-

cordance with Underwriters Laboratories, Inc. Standard 

UL-489 and satisfy the requirements of the International 

Electrotechnical Commission Recommendations No. IEC 

60947-2.

Th

Trip Units are AC only devices that 

employ

microprocessor based technology that provides 

true

RMS current sensing means for proper correlation

with thermal characteristics of conductors and equipment.  

The primary function of the Trip Unit is circuit protection.  

This is achieved by analyzing the  secondary current

signal received from the circuit breaker current sensors and 

initiating trip signals to the circuit breaker shunt trip when 

pre-set current levels and time delay setting are exceeded.  

Low level ground fault protection with an adjustable time 

delay is supplied when appropriate trip types are selected.

In open air at 40º C, a N-Frame Circuit Breaker with a  

Trip Unit will carry continuously up to 1200 amperes without 

exceeding a 50º C rise at the terminals.  The calibration 

of the trip unit is insensitive to ambient temperatures over 

a range of -20º to +55º C.  However, the trip unit contains 

thermal temperature protective circuitry that initiates a trip 

operation for self-protection if the internal ambient tem-

perature at the printed circuit board (PCB) reaches approxi-

mately 90º C.  For ambient conditions above 40º C, derat-

ing of the circuit breaker should be considered to avoid 

exceeding a safe terminal temperature operation range.  

Consult 

Allen-Bradley

 for recommendations.

Figure 1-1 N-Frame Circuit Breaker

Bul. 140

U

Содержание Allen-Bradley 140U

















Отзывы: