Rockwell Automation 700-1308-00 Скачать руководство пользователя страница 79

Страница: 79 / 138

Maintenance

Repair

MagneMover LITE Service Manual

Rockwell Automation Publication MMI-UM037A-EN-P - April 2020

Procedure

Figure 20: Remove Curve Motor Guide Rail

Remove Pucks

Stop all motion on the section of the MagneMover LITE transport system where the
puck is being removed.

Remove the inside guide rail from a curve motor.

NOTE:

DO NOT remove the rails from the switches.

Remove the two screws that secure the V-braces to the guide rail.

Remove the two screws that secure the guide rail to the motor.

Lift the guide rail off the motor.

Remove pucks by sliding them from the adjacent motors into the open curve.

NOTE:

Once pucks are removed from the transport system, they must be stored in
their original packaging to help protect the pucks and to minimize any safety
risks.

Replace the guide rail by reversing

Step 2

Apply Loctite 243 to the screws.

Tighten the guide rail mounting screw and the V-brace hardware to 3.4 N•m
[30 in•lb].

NOTE:

The Loctite must cure for 2 hours at 22° C [72° F] before using the
transport system.

Return the MM LITE transport system to normal operation.

V Brace Screw

Guide Rail

(2X)

Mounting Screws

(2X)

Содержание 700-1308-00











































































































































Результаты поиска

Содержание 700-1308-00

Отзывы:

Rockwell Automation 700-1308-00, Руководство по обслуживанию, Страница: 79 / 138

Результаты поиска

Содержание 700-1308-00

Отзывы: