manualshive.com logo in svg

Rockwell Automation 440R-D22R2, Руководство пользователя

Поделиться
Скачать
Rockwell Automation 440R-D22R2 Скачать руководство пользователя страница 72

72

Rockwell Automation Publication 440R-UM013F-EN-P - July 2021

Chapter 11          Troubleshooting

Auxiliary Output Issues

Measure the Auxiliary Output Terminal Voltage

When OUT status indicator is OFF, my PLC does not know that the relay is OFF 
or my auxiliary status indicator does not turn ON.

Confirm that voltage is present at the relay terminals and the load. 

Figure 83

 

shows an example of the measurement points for one output channel (41/42). 

Figure 83 - Measure Voltage Aux Output Terminals

Measure the Contact Resistance

The OUT status indicator is OFF, and the voltage at terminal 41 is the same as 
the supply voltage. However, terminal 42 measures 0V.

Table 18 - Auxiliary Output Issues

State

Symptom

Action

The OUT status indicator is 
OFF.

My PLC does not know that the relay is OFF or my auxiliary status 
indicator does not turn ON.

See 

Measure the Auxiliary Output Terminal Voltage on page 72

.

The voltage at terminal 41 is the same as the supply voltage. However, 
terminal 42 measures 0V.

See 

Measure the Contact Resistance on page 72

.

Terminal Y32 does not turn ON.

See 

Check the Y32 Output on page 73

.

Terminal X32 does not turn ON.

See 

Check the X32 Output on page 74

.

The safety outputs are OFF.

The Y32 output must be ON. This is true for both faulted and running 
states.

See 

Check the Y32 Output on page 73

.

For more information on auxiliary outputs, see 

Auxiliary Output on page 27

.

Step

Description

1

The voltage at 41 must be the same as the supply voltage. If not, check for an open circuit (broken 
wire), blown fuse, or tripped circuit breaker.

2

The voltage at 42 must be the same as the supply voltage. If not, the positive-guided relay inside GSR 
safety relay is not closing. Measure the contact resistance; see 

Figure 84 on page 73

.

3

The voltage at the PLC input must be the same as the supply voltage. If not, check for an open circuit 
(broken wire), a bad contact at a terminal connection), or go to step 4.

4

Place the black test probe on the PLC common terminal. Verify that the common of the PLC is 
connected to the common of the voltage supply.

5

The aux output voltage at one side of the auxiliary status indicator must be the same as the supply 
voltage. If not, check for an open circuit (broken wire) between terminal 14 and aux status indicator.

6

Verify that the aux status indicator is connected to the voltage supply common. The aux status 
indicator must be replaced.

42

+Vs

41

Volts

DMM

1

2

3

4

5

Com

OUT

6

+V supply

0V

PLC

Input

Содержание 440R-D22R2



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды