manualshive.com logo in svg

Rockwell Automation 440R-D22R2, Руководство пользователя

Поделиться
Скачать
Rockwell Automation 440R-D22R2 Скачать руководство пользователя страница 66

66

Rockwell Automation Publication 440R-UM013F-EN-P - July 2021

Chapter 11          Troubleshooting

Figure 73 - Momentary Interruption of SWS Input

Check the Reset/Monitoring 
Circuit (Step 5)

The OUT status indicator blinks green when the inputs to the GSR safety relay 
are satisfied and the GSR safety relay is ready to turn on its outputs. The OUT 
status indicator flashes green at a 1 Hz rate. The GSR safety relay is waiting for 
the appropriate reset signal at terminal S34.

If the OUT status indicator is flashing green, but the relay does not turn on its 
outputs when the reset button is pressed, measure the voltage at terminal S34 
(point 1) as shown in 

Figure 74

. If 24V is not present when the reset button is 

pushed, then check the other connections (points 2...7) in the circuit. If 24V is 
present at terminal S34, then you must consider the reset configuration:

•

Automatic/Manual:

 The GSR safety relay must be replaced as the output 

indicator must turn steady green as soon as the voltage was present at 
terminal S34.

•

Monitored/Manual:

 If the output indicator does not turn steady green 

when voltage at S34 is present between 0.25…3 seconds, then GSR safety 
relay must be replaced.

Figure 74 - Measure Reset/Monitoring Circuit Voltage

Command to open SWS

SWS opens

SW closes in 5.7 ms

The Downstream unit 
turns off its Output

The Downstream unit 
turns its Output back 
on auto-reset

+24V DC

24V DC Com

S34

OUT

A1

A2

1

2

3

4

5

6

7

24

Volts

DMM

Содержание 440R-D22R2



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды