-2dB
-4dB
ON
OFF
0dB
Tweeter (+)
Do Not Use
Tweeter
(TWT)
Connect Only
ONE (+) Terminal
Connect Only
ONE (+) Terminal
INPUT
-4dB
-2dB
0dB
NEG
OUTPUT AXIS
NEG
OFF
ON
Tweeter On-Axis
Tweeter Off-Axis
OUTPUT
AXIS
OFF
ON
OUTPUT
AXIS
OFF
ON
Tweeter (+)
Do Not Use
3
Specifications subject to change without notice.
See figures on following pages.
T2 Components
T252-S
T2652-S
T2T-S
Nominal Diameter - inch (mm)
5.25 (133)
6.5 (165)
1.0 (25.4)
Description
Component System Component System
Tweeter System
Nominal Impedance (ohms)
4Ω
4Ω
4Ω
Frequency Response (Hz)
65Hz - 20kHz
55Hz - 22kHz
3kHz - 22kHz
Crossover Frequency (Hz)
3.5kHz
3kHz
3kHz
High-Pass Butterworth Crossover
18dB/octave
18dB/octave
18dB/octave
Low Pass Butterworth Crossover
12dB/octave
12dB/octave
–
Voice Coil Diameter - inch (mm)
1.1 (28)
1.2 (31)
1.0 (25.4)
Fs - Free Air Resonance (Hz)
65
55
1.8kHz
Qts
0.60
0.50
–
Vas - cu. ft. (Liter)
0.34 (9.6)
0.56 (16)
–
Xmax - inch (mm)
0.16 (4.0)
0.24 (6.0)
–
SPL (dB @ 1w/1m)
87 dB
89 dB
90 dB
Power Handling-Watts (RMS / Peak)
75 / 150
100 / 200
75 / 150
Rec. Amp Power-Watts (RMS)
22.5W ~ 75W
30W ~ 100W
22.5W ~ 75W
Mounting Diameter-inch (mm)
4.80 (122)
5.59 (142)
1.75 (45) (Flush Mount)
Mounting Depth-inch (mm)
2.03 (52)
2.51 (64)
0.95 (24) (Flush Mount)
Includes Grille/Trim Ring
YES
YES
YES
Trim Ring Diameter-inch (mm)
6.22 (158)
6.949 (177)
2.13 (54)
Trim Ring Height-inch (mm)
1.06 (27)
1.18 (30)
0.31 (8)
Includes Adapter Plate
5"x7"/6"x9"
5"x7"/6"x9"
NO
S
PECIFICATIONS
W
IRING
F
EATURES
Discreet Dual Clamp (DDC™)
Tweeter Mount
Every aspect of the new Tweeter design has been
completely re-engineered to allow for maximum
ease of installation and fitment.This optimized
patent pending design provides concentric
clamping pressure around the perimeter of the
mounting hole.
The “mounting cups” are in fact not “cups” at all,
but rather unobtrusive “clamps” that quickly
and easily mount in a standard 1.75 inch (45mm)
hole saw opening with a single center screw
securing with balanced pressure to both faces
of the mounting surface. From there, the tweeter
simply snaps into place and is secured by a
snap-on trim ring. Removal is easy if needed.
The protective grille on the tweeter is
non-removable and an intergral part of the design.
T2T-S
Crossover Wiring
1. Use illustration for proper connection.
2. Be sure to maintain speaker polarity.
3. Connecting the positive wire to 0dB matches the
amplitude of the tweeter to the mid-range (woofer).
4. Connecting positive wire to -2dB or -4dB to reduce
the amplitude of the tweeter -2dB or -4dB lower
than the mid-range, (ideal for tweeters located high
in door panels and mid-range low in the kick panel).
