Rockford Fosgate Power 250.1 Скачать руководство пользователя страница 56

Страница: 56 / 61

Opération stéréo/mono (Tri-
mode)

• Les entrées

RCA

sont connectées aux canaux gauche et droit

•

L'interrupteur “Signal Input”

doit se trouver dans la position “Unbalanced” pour

utiliser l'entrée RCA

•

L'interrupteur “Left Phase”

doit se trouver dans la position “0

”

•

L'interrupteur “Right Phase”

doit se trouver dans la position “180

” pour opera-

tion en tri-mode

• Les gains des canaux gauche et droit sont réglés de la même manière pour

équilibrer le subwoofer

•

L'impédance

de chaque canal devrait être de

minimum 2

Ω

•

L'impédance

du canal mono devrait être de

minimum 4

Ω

• Les

XCards

sont introduites sur

fall range

• Il est conseillé d'utiliser les filtre passifs lorsqu'on fait fonctionner l'amplificateur en

tri-mode

•

NE connecter AUCUN

des câbles HP à la masse au risque d'un fonctionnement

instable.

•

Les filtres passifs

sont nécessaires pour une utilisation correcte stereo/mono

– 53 –

Unbal.

Pass

Thru

Bal.

Input

-180

E Z - 1 8 0

- 0

Bridged

Gain

Bal.

Gain

–

RCA

Input

–

Ω

min.

–

Speaker

Terminal

–

Speaker

Terminal

Speaker

+ L –

Speaker

– R +

L (Mono)

Ω

min.

Ω

min.

RANÇAIS

Содержание Power 250.1






























































Результаты поиска

Содержание Power 250.1

Отзывы:

Rockford Fosgate Power 250.1, Эксплуатация и установка, Страница: 56 / 61

Результаты поиска

Содержание Power 250.1

Отзывы: